No Compression on 1 and 4
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
No Compression on 1 and 4
20 Dec 2011 18:28
Just finished my rebuild. Had the valves redone at a shop and my cylinders bored out from some gnarly rust that froze it up. Cylinders 1 and 4 now have 0 psi for compression. 2 and 3 both get 125 easily. It's not the piston, did the oil check, and there was no difference. The timing is also not the issue. I'm gonna do a valve clearance check, but I want to know if there's anything else I should be aware of.
Thanks
-E
Thanks
-E
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: No Compression on 1 and 4
20 Dec 2011 19:01
Sounds like cam/valve timing or valve clearance to me. The fact that both 1 and 4 are sharing the issue seems more likely cam/valve timing, but could easily be clearances too if the cylinder head has been worked on or buckets were swapped around.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: No Compression on 1 and 4
20 Dec 2011 19:02
Also, piston rings could be the issue if the gap is all lined up, but I would expect low compression then, not 0psi.
A leak down tested would make it obvious.
Cheap and works well: www.harborfreight.com/cylinder-leak-down-tester-94190.html
A leak down tested would make it obvious.
Cheap and works well: www.harborfreight.com/cylinder-leak-down-tester-94190.html
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: No Compression on 1 and 4
20 Dec 2011 19:08
Also make sure the cams aren't mixed up or in backwards. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: No Compression on 1 and 4
20 Dec 2011 20:55
Yeah whats been said... :laugh: 1 or both valves per cylinder are staying/stuck open -fix that. Clearances/cams obviously + buckets guides sliding nicely...
You can get some surprisingly good compression with the ring gaps lined up and oil in there - so it aint that for sure.
Good luck.
You can get some surprisingly good compression with the ring gaps lined up and oil in there - so it aint that for sure.
Good luck.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: No Compression on 1 and 4
20 Dec 2011 23:21
I'll check the clearances, which I think is the issue. I had it all mounted before and had it skewed unfortunately, so I think i should test the valves. I might've bent one. :ohmy: I'll pick up that tester from Harbor Freight and check it.
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: No Compression on 1 and 4
20 Dec 2011 23:40
The nice thing about a leak down is that there's no guessing. It' obvious.
You can make one yourself if you want, others have done it, but the one from HF is actually fairly nice for the money.
You can make one yourself if you want, others have done it, but the one from HF is actually fairly nice for the money.
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: No Compression on 1 and 4
21 Dec 2011 14:18TeK9iNe wrote: Yeah whats been said... :laugh: 1 or both valves per cylinder are staying/stuck open -fix that. Clearances/cams obviously + buckets guides sliding nicely...
You can get some surprisingly good compression with the ring gaps lined up and oil in there - so it aint that for sure.
Good luck.
Absolutely true, hole in the piston or valve(s) stuck open are the cause for zero compression. Can't be cams because they would affect all four cylinders equally.
KD9JUR
Please Log in or Create an account to join the conversation.
- Breaker19
-
- Offline
- User
-

Registered
- Posts: 88
- Thanks: 2
Re: No Compression on 1 and 4
22 Dec 2011 16:04
Sounds like cam timing, 180 degrees off. I just reset the timing on this KZ1100 and somehow it got that far off (lucky I didn't bend any valves)... I rotated the crank around again, reset the cams at that point and get 150-160 psi on all 4.
2003 Suzuki DR650 Dual-Sport
1982 KZ1100A2 - GONE! Traded-in for a '12 Concours 14
www.facebook.com/pages/Moto-Resto/169238286503527
1982 KZ1100A2 - GONE! Traded-in for a '12 Concours 14
www.facebook.com/pages/Moto-Resto/169238286503527
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: No Compression on 1 and 4
23 Dec 2011 01:02 - 23 Dec 2011 01:02Breaker19 wrote: Sounds like cam timing, 180 degrees off. I just reset the timing on this KZ1100 and somehow it got that far off (lucky I didn't bend any valves)... I rotated the crank around again, reset the cams at that point and get 150-160 psi on all 4.
Since he has 0 psi on 1 and 4, and 125 psi on 2 and 3, does that mean that if he moves the cams 180 degrees he'll have 125 psi on 1 and 4 and 0 psi on 2 and 3?
Those must be some really wild cams
KD9JUR
Last edit: 23 Dec 2011 01:02 by steell.
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- baldy110
-
- Offline
- User
-

Registered
- Posts: 2272
- Thanks: 512
Re: No Compression on 1 and 4
23 Dec 2011 13:25
No, it just means he was off 1 tooth on the cam chain. This would keep the valves slightly open when the piston is at top dead center on #1 and #4. Very common mistake when assembling.
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: No Compression on 1 and 4
24 Dec 2011 13:09
Assuming you're saying the intake cam is installed 1 tooth retarded, thus holding the intake valve open later, then you're saying that only 1 and 4 are retarded while 2 and 3 are not?
Still can't visualize any way that would be possible.
Still can't visualize any way that would be possible.
KD9JUR
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
