clutch problem
- 916kzbobber
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
clutch problem
21 Dec 2011 20:03
my 79 kz has a 85 gpz 750 motor in it and when i was riding it today the clutch toped ingaugeing so i adjusted the clutch from the side cover and it seemed to work then it happened again so i tightened up again and now when i pull in clutch lever its super tight and when bike is running the motor wants to stall out any adivse thanks
Please Log in or Create an account to join the conversation.
- KraZy Chris
-
- Offline
- User
-

Registered
- Posts: 95
- Thanks: 0
Re: clutch problem
22 Dec 2011 01:00
Im no expert by any means but I did have a clutch cable go bad while I was riding once. Sometimes they stretch before breaking.
78 KZ1000, Middle TN
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: clutch problem
22 Dec 2011 02:34
If the problem is disengaging the clutch (pulling in the lever to shift), I would suggest first to check and make sure the bolts holding the engine sprocket cover are still there, and not loose (use some blue loctite if they vibrated loose on you). If that is ok, then loosen your clutch cable adjustment, then adjust the clutch pushrod according to the specs in your manual (it varies slightly by model), then re-tighten the clutch cable according to specs (usually 2-3mm of play).
If the clutch itself is slipping, then you may need to pull the clutch cover off to inspect the plates, and the springs. Certain types of newer oils (I think they show the words "friction modifiers" on the labels) are not good for our clutches, so an oil change could be in order as well.
If the clutch itself is slipping, then you may need to pull the clutch cover off to inspect the plates, and the springs. Certain types of newer oils (I think they show the words "friction modifiers" on the labels) are not good for our clutches, so an oil change could be in order as well.
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Please Log in or Create an account to join the conversation.
- Fritula
-
- Offline
- User
-

Registered
- holly land garage
- Posts: 46
- Thanks: 0
Re: clutch problem
22 Dec 2011 03:22
I beleive you clutch cable sleve is gone.Clutch plates can not go that fast.So after first time hapened you adjusted it...it was good til the next one.Than you adjust it again.Now you came to the point where cable is to short and when puling the lever your clutch plates are pressed to much and you fill engine goes down a bit. Check for the cable sleve ends on both side of cable.Hope it helps.
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: clutch problem
22 Dec 2011 06:00
run some penetrating oil down the cable, that should work, if not then replace cable
Please Log in or Create an account to join the conversation.
- 916kzbobber
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: clutch problem
22 Dec 2011 14:43
thanks guys i have sprayed penitrating oil in the canle housing didnt seem to work so i am getting a clutch cable today thanks for allthe help will post pics soon
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
