clutch wont disingauge
- 916kzbobber
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
clutch wont disingauge
27 Dec 2011 18:56
i have replaced clutch cable and have tried adjusting ever which way i can imagine and with clutch handle pulled in still wont disingaude the clutch im stumped could clutxh be bad it did slip a little in high rpms but ran fine anyhelp would be greatly apreciated its a 79 kz750
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: clutch wont disingauge
27 Dec 2011 20:22
Weight, and type of engine oil being used? Most "Car Oils" are not compatable with wet plate clutches in these older bikes.
Best Oils To Use In Your Bike (Just My Opinion)
Engine oil : The commercial grade oils are clearly superior to the mass market oils. For the best protection in your bike or car, use Shell Rotella Synthetic, available at Wal-Mart in blue containers . For the best petroleum oil you can buy, get Shell Rotella T, Mobil Delvac 1300, or Chevron Delo 400, available at any auto parts store. On the back of most oil cans is a circular stamp with the certification. Avoid oils that say "energy conserving" in the bottom half of the donut.
These oils contain friction modifier additives that could cause clutch slipping over time. The EPA mandated certain gas mileage, so the auto makers turned to the oil manufacturers who came up with friction modifiers of the oil to meet these new standards. All XXw-20 and XXw-30 oils are energy conserving, and should not be used in your motorcycle. Don't buy any oil additives like STP or Slick-50. Here's several listings on all about oil justifying these conclusions.
The Recommended Synthetic Oils :
Shell Rotella Synthetic
5w-40 Delvac 1 Synthetic
5w-40 Mobil-1 SUV/Truck Synthetic
5w-40 AMSOil AMF Synthetic (pricey, but it’s your money)
10w-40 Golden Spectro Synthetic
10w-50 Motul 5100 Synthetic
10w-40 Mobil-1 Synthetic
15w-50 Mobil-1 MX4T Synthetic
The best synthetics are: (in no particular order)
Shell Rotella-T Synthetic 5w-40 (blue container is synthetic, not white which is dino), gallon at Wal-Mart.
Mobil Delvac-1 5w-40 (grey container is synthetic, not black which is dino), gallon at Petro stations, gallon at Farm and Fleet.
Mobil-1 SUV 5w-40, qt anywhere.
AMSOil AMF 10w-40 synthetic motorcycle oil. (again, pricey)
Golden Spectro Supreme, (no price).
Motul 5100 Ester, (no price).
Mobil-1 automotive oils all contain small amounts of moly - about 100 to 200 ppm. This can cause clutch slippage in some motorcycles. I've only heard of this being a problem in Honda Shadows.
The Recommended Petroleum Oils
Chevron Delo 400 15w-40
Delvac 1300 15w-40
Shell Rotella 15w-40
The best petroleum oils are: (in no particular order)
Chevron Delo 400 15w-40 (blue container) gallon at any auto parts store, gallons at Costco.
Mobil Delvac 1300 15w-40 (black container) gallon at any auto parts store, gallons at Sam's Club.
Shell Rotella-T 15w-40 (white container) gallon at Wal-Mart or any auto parts store, gallons at Sam's Club.
Castrol 15w-40 (Green container) gallon at Wal-Mart or any auto parts store, gallons at Sam’s club.
Best Oils To Use In Your Bike (Just My Opinion)
Engine oil : The commercial grade oils are clearly superior to the mass market oils. For the best protection in your bike or car, use Shell Rotella Synthetic, available at Wal-Mart in blue containers . For the best petroleum oil you can buy, get Shell Rotella T, Mobil Delvac 1300, or Chevron Delo 400, available at any auto parts store. On the back of most oil cans is a circular stamp with the certification. Avoid oils that say "energy conserving" in the bottom half of the donut.
These oils contain friction modifier additives that could cause clutch slipping over time. The EPA mandated certain gas mileage, so the auto makers turned to the oil manufacturers who came up with friction modifiers of the oil to meet these new standards. All XXw-20 and XXw-30 oils are energy conserving, and should not be used in your motorcycle. Don't buy any oil additives like STP or Slick-50. Here's several listings on all about oil justifying these conclusions.
The Recommended Synthetic Oils :
Shell Rotella Synthetic
5w-40 Delvac 1 Synthetic
5w-40 Mobil-1 SUV/Truck Synthetic
5w-40 AMSOil AMF Synthetic (pricey, but it’s your money)
10w-40 Golden Spectro Synthetic
10w-50 Motul 5100 Synthetic
10w-40 Mobil-1 Synthetic
15w-50 Mobil-1 MX4T Synthetic
The best synthetics are: (in no particular order)
Shell Rotella-T Synthetic 5w-40 (blue container is synthetic, not white which is dino), gallon at Wal-Mart.
Mobil Delvac-1 5w-40 (grey container is synthetic, not black which is dino), gallon at Petro stations, gallon at Farm and Fleet.
Mobil-1 SUV 5w-40, qt anywhere.
AMSOil AMF 10w-40 synthetic motorcycle oil. (again, pricey)
Golden Spectro Supreme, (no price).
Motul 5100 Ester, (no price).
Mobil-1 automotive oils all contain small amounts of moly - about 100 to 200 ppm. This can cause clutch slippage in some motorcycles. I've only heard of this being a problem in Honda Shadows.
The Recommended Petroleum Oils
Chevron Delo 400 15w-40
Delvac 1300 15w-40
Shell Rotella 15w-40
The best petroleum oils are: (in no particular order)
Chevron Delo 400 15w-40 (blue container) gallon at any auto parts store, gallons at Costco.
Mobil Delvac 1300 15w-40 (black container) gallon at any auto parts store, gallons at Sam's Club.
Shell Rotella-T 15w-40 (white container) gallon at Wal-Mart or any auto parts store, gallons at Sam's Club.
Castrol 15w-40 (Green container) gallon at Wal-Mart or any auto parts store, gallons at Sam’s club.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: clutch wont disingauge
27 Dec 2011 21:52 - 27 Dec 2011 21:58
Just to clarify some terms:
"Engaged" is when the rear wheel is connected to the motor, motor turns wheel turns.
"Disengaged" Is when the motor revs freely in gear but the wheel don't turn.
Please describe what happens as you start the motor, put it in gear, and try to take off.
Edit:
Off hand guesses, when you removed the sprocket cover to replace the clutch cable the clutch push rod slid out and the little ball behind it fell out and disappeared. Or you rotated the lever that the clutch cable hooks to under the sprocket cover forward and it slipped to the next slot.
"Engaged" is when the rear wheel is connected to the motor, motor turns wheel turns.
"Disengaged" Is when the motor revs freely in gear but the wheel don't turn.
Please describe what happens as you start the motor, put it in gear, and try to take off.
Edit:
Off hand guesses, when you removed the sprocket cover to replace the clutch cable the clutch push rod slid out and the little ball behind it fell out and disappeared. Or you rotated the lever that the clutch cable hooks to under the sprocket cover forward and it slipped to the next slot.
KD9JUR
Last edit: 27 Dec 2011 21:58 by steell.
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- 916kzbobber
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: clutch wont disingauge
28 Dec 2011 04:33
steell when i start bike pull in clutch bike still moves forward with clutch pulled in hope that definition helps
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Please Log in or Create an account to join the conversation.
- 916kzbobber
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: clutch wont disingauge
28 Dec 2011 04:41
this is what happened i put z bars on bike. rode bike about 5 miles and the clutch would not work ie pull in clutch bike still moved forward so trye to adjust on the clutch lever no go tryed to adjust by the clutch actuator worked test drove bike and 500 yards later same thing so i thought maybe it was a stretched cable replaced it and now same thing put bike in gear pull clutch bike still in gear idk please help i just want to ride
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: clutch wont disingauge
28 Dec 2011 09:34
Do you have a manual?
theres 3 differant adjustments on the clutch/cable,differant models get adjusted in differant order
theres 3 differant adjustments on the clutch/cable,differant models get adjusted in differant order
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: clutch wont disingauge
28 Dec 2011 09:51 - 28 Dec 2011 09:53
As some manuals provide erroneous push rod adjustment instructions, would try reversing direction of turns on the actuator screw when adjusting the push rod.
For example, some actuator designs require initial seating by first turning the adjustment screw counter-clockwise until it seats, and then clockwise 1/4 turn to provide the slight gap required.
Whereas other actuator designs require initial seating by first turning the adjustment screw clockwise until it seats, and then counter-clockwise 1/4 turn to provide the slight gap required.
Would make another attempt to adjust the push rod, but this time using the opposite turning sequence.
Also assure that the actuator hasn't dislocated itself by having been over-extended.
Good Fortune!
For example, some actuator designs require initial seating by first turning the adjustment screw counter-clockwise until it seats, and then clockwise 1/4 turn to provide the slight gap required.
Whereas other actuator designs require initial seating by first turning the adjustment screw clockwise until it seats, and then counter-clockwise 1/4 turn to provide the slight gap required.
Would make another attempt to adjust the push rod, but this time using the opposite turning sequence.
Also assure that the actuator hasn't dislocated itself by having been over-extended.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 28 Dec 2011 09:53 by Patton.
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: clutch wont disingauge
28 Dec 2011 10:17
You may want to try this for I had similar experience with all new clutch components/adjustments in my KZ900 build.
Out of the OEM 1980-1988 Service manual.
Instead of turning in "Until it becomes hard"....
Turn in in until you just feel it make contact then lock her down and continue with the rest of the adjustments...
OMR
In case you need...
Out of the OEM 1980-1988 Service manual.
Instead of turning in "Until it becomes hard"....
Turn in in until you just feel it make contact then lock her down and continue with the rest of the adjustments...
OMR
In case you need...
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: clutch wont disingauge
28 Dec 2011 10:38
does his have a ball and actuator rod ??? if so maybe ball fell out, just a guess
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: clutch wont disingauge
28 Dec 2011 10:50
From the clutch parts diagram at kawasaki.com, the actuator assembly appears to be the "ball and ramp" style.
Am thinking that the "ball and ramp" style clutch push rod adjustment is to first turn the screw counter-clockwise until it seats, then 1/4 turn clockwise to provide the required small gap.
Good Fortune!
Am thinking that the "ball and ramp" style clutch push rod adjustment is to first turn the screw counter-clockwise until it seats, then 1/4 turn clockwise to provide the required small gap.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: clutch wont disingauge
28 Dec 2011 12:01
Ok, so you started out for a ride and the clutch worked fine, but 5 miles later the clutch didn't work any more?
I would pull the clutch cover off and check the clutch basket to see if it moves in and out a bit. Maybe the nut that holds the clutch on came loose. At that time you can squeeze the clutch lever and see what happens at the clutch also.
I would pull the clutch cover off and check the clutch basket to see if it moves in and out a bit. Maybe the nut that holds the clutch on came loose. At that time you can squeeze the clutch lever and see what happens at the clutch also.
KD9JUR
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
