Valve shim, Zero clearance.
- 750formula
-
Topic Author
- Offline
- User
-

Registered
- Posts: 4
- Thanks: 0
Valve shim, Zero clearance.
03 Jan 2012 23:43
Well i think that the title says it all. I rebuilt the entire motor. Lapped the valves, I just put it all back together and checked the valve clearances and low and behold all but two are zero. I don't want to order 4 of the smallest shims just to guess, I'm wondering if there is a way to get a good starting point that does not involve takeing all of the valves back out.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Valve shim, Zero clearance.
03 Jan 2012 23:49
? You won't need to remove the valves to replace the shims. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- 750formula
-
Topic Author
- Offline
- User
-

Registered
- Posts: 4
- Thanks: 0
Re: Valve shim, Zero clearance.
03 Jan 2012 23:54
I would only need to remove the valves if i wanted to measure the stem installed height. I would like to know if there is a trick to selecting the proper shim without ordering them twice. IOW ordering the 2mm shims and them using a feeler gauge to check the gap, then ordering the proper shims.
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: Valve shim, Zero clearance.
04 Jan 2012 00:02
u might as well get used to the fact that u will, in the course of toying with it, NEED several different sizes, order a few of each or as I did , find a friend who uses the same shims and go in halves on a set
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Valve shim, Zero clearance.
04 Jan 2012 00:03750formula wrote: I would only need to remove the valves if i wanted to measure the stem installed height. I would like to know if there is a trick to selecting the proper shim without ordering them twice. IOW ordering the 2mm shims and them using a feeler gauge to check the gap, then ordering the proper shims.
Oh, now I understand. Unfortunately, I don't know of a way other than what you describe - put in smallest shims, measure, then order necessary shims. Maybe someone else has a trick that will work. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- Jeff.Saunders
-
- Offline
- Vendor
-

Vendors
- Posts: 1238
- Thanks: 149
Re: Valve shim, Zero clearance.
04 Jan 2012 08:46
The key is to know what clearance you had BEFORE you tore the engine down, and then what shim thicknesses are in each bucket now.
If you shuffled the buckets and shims, then there's no way of even guessing what's where.
Typical lapping of the valves should only drop your clearances 1-2 thou. Cutting valve seats will cause at least a 2-3 shim thickness change - sometimes more depending how heavy-handed the machine shop was...
If you can spin the bucket, but can't get a feeler gauge under the cam, you can assume 1 thou clearance and adjust from that. If you cannot spin the bucket, then it suggests you probably shuffled the buckets / shims during reassembly.
If you shuffled the buckets and shims, then there's no way of even guessing what's where.
Typical lapping of the valves should only drop your clearances 1-2 thou. Cutting valve seats will cause at least a 2-3 shim thickness change - sometimes more depending how heavy-handed the machine shop was...
If you can spin the bucket, but can't get a feeler gauge under the cam, you can assume 1 thou clearance and adjust from that. If you cannot spin the bucket, then it suggests you probably shuffled the buckets / shims during reassembly.
Please Log in or Create an account to join the conversation.
- Godfrey
-
- Offline
- User
-

Registered
- Posts: 210
- Thanks: 10
Re: Valve shim, Zero clearance.
04 Jan 2012 19:46
well its a lot more work but you could order 1 2 mm shim and take each cam out 4 times, putting that shim under each bucket( oh yeah you only have to do it 6 times)and measuring , and then calculate and order the shims you need
1981 650CSR frame
1980 KZ750E engine
1980 KZ750E engine
Please Log in or Create an account to join the conversation.
- elfmagic17
-
- Offline
- User
-

Registered
- Posts: 334
- Thanks: 24
Re: Valve shim, Zero clearance.
05 Jan 2012 00:59
Just a Idea for under bucket shims, never tried it but it should get you close as hell. Remove One bucket at a time and carefully reinstall the cam with the lobe up away from the shim. Measure clearance at the cam and shim, then measure thickness of bucket in the center. Subtract that from clearence. should leave you with total clearence. Add needed clearence and compare with the thickness of the shim and figure what new smaller shim size is needed. Reinstall bucket and move to next valve so not to damage cam. Anyone think this will work? I was gonig to do it with my engine untill I tipped the valves and got my clearence within spec.(already had the head off)
Kenny Hicks
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
Please Log in or Create an account to join the conversation.
- elfmagic17
-
- Offline
- User
-

Registered
- Posts: 334
- Thanks: 24
Re: Valve shim, Zero clearance.
05 Jan 2012 01:02Godfrey wrote: well its a lot more work but you could order 1 2 mm shim and take each cam out 4 times, putting that shim under each bucket( oh yeah you only have to do it 6 times)and measuring , and then calculate and order the shims you need
No you were right, 8 you have to get the shim in there in the first place to measure the first time.
Kenny Hicks
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Valve shim, Zero clearance.
05 Jan 2012 02:44
You can usually find a shim kit with every size you'll ever need for the cost of what a dealer will sell you about three shims.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- Godfrey
-
- Offline
- User
-

Registered
- Posts: 210
- Thanks: 10
Re: Valve shim, Zero clearance.
05 Jan 2012 09:13
I changed the cams out in my 750 about a month ago, and did exactly what I said earlier, found used shims on e bay for 5.99 a piece no shipping. Around here the dealer wantsya to buy what ya need and they get the old shim to boot.
1981 650CSR frame
1980 KZ750E engine
1980 KZ750E engine
Please Log in or Create an account to join the conversation.
- roy-b-boy-b
-
- Offline
- User
-

Registered
- Posts: 3245
- Thanks: 103
Re: Valve shim, Zero clearance.
05 Jan 2012 11:28
Get a 200 shim and then measure to find the size you need. Or find the thinnest shim you have and use it for checking if it will fit on all valves. Roy
1979 LTD Street Fighter.1977 KZ1000
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
