stuck exhaust valves

  • kzminion
  • kzminion's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

stuck exhaust valves

06 Jan 2012 19:52
#496793
I have a 1982 kz750 Spectre. I just bought it in late July after riding it for the summer I decided to renovate it after I noticed a couple if grease spots on the outside of the engine. After completely tearing the engine down and cleaning it up, I tried to take out the Tappets on the exhaust side out,but they are completely stuck in. I took a iridium magnet to them but to no success. The intake side is fine. I don't want to take heat to the head so it doesn't warp it. now have WD40 soaking it. What should I do?


Attachment valves.png not found

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: stuck exhaust valves

06 Jan 2012 20:57
#496807
I just went through this with one of the exhaust valves in my 750 head for my racer project. I couldn't get it to budge, rotate, nothing.

My solution (not necessarily the best) was to do the following:
1. Make sure the area around the bucket is clean.
2. Soak the area with WD40 or other lube (engine oil, whatever).
3. Lay a leather glove over the bucket.
4. take a bolt with a big head on it, place the head on the leather glove (over the bucket)
5. Strike the bolt tip (not the head, that's on the bucket) with a hammer a few times.

This should push the bucket in and depress the valve slightly (don't whack it really hard) and protect the surface of the bucket enough to keep it from getting marred. As the bucket depresses the lubricant was able to move in around the bucket and it would then spin freely.

I think I had to do it a few times, but noticed an improvement in "freeness" the first time. Then used a magnet to pull the bucket out (it was rotating completely free before I tried to remove it).

I tried heat from a hand held propane torch and didn't get anywhere. I also tried soaking it and it didn't seem to help.

Disclaimer: Your mileage may vary, I don't really have a clue what I'm doing - just have big hands and bigger hammers.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: stuck exhaust valves

06 Jan 2012 21:51
#496817
I think Kroil is better than WD-40.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: stuck exhaust valves

06 Jan 2012 21:58
#496821
bountyhunter wrote: I think Kroil is better than WD-40.
I know zep45 works better than all of them! :woohoo:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • kzminion
  • kzminion's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Re: stuck exhaust valves

19 Jan 2012 09:31
#498846
DoubleDub I want to thank you, I took you advice but unfortunately to no avail. I had to bring it to the shop and for 35 dollars they stuck it in a ultrasonic cleaner and they came out plus now i don't have to clean the carbon out of the intake and exhaust ports. :lol:

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: stuck exhaust valves

19 Jan 2012 09:36
#498847
That sounds like a bargain to me! I would stay friendly with that shop; you never know what else you may need done. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: stuck exhaust valves

19 Jan 2012 09:46
#498848
Don't be afraid to put some heat to the problem. Just use common sense if you use a torch. Heat, penetrating oil and some tapping should do the trick. A valve lapping stick is preferable to a magnet for pulling buckets out of the bores.
Larry C.

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: stuck exhaust valves

19 Jan 2012 11:05
#498860
Good info, thanks, Larry.

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: stuck exhaust valves

19 Jan 2012 20:49
#498961
I had some valve springs break in a head one time. I had to weld a bolt to one of the buckets to get it out...that's no BS
Larry C.

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: stuck exhaust valves

19 Jan 2012 21:14
#498968
LarryC wrote: I had some valve springs break in a head one time. I had to weld a bolt to one of the buckets to get it out...that's no BS

I know on the 900/1000 heads the camshaft caps were specific to their location/head pairing. Are the buckets like that at all on these heads? Can you get just any other bucket of the same size/type to swap out after something like that?

Please Log in or Create an account to join the conversation.

  • kzminion
  • kzminion's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Re: stuck exhaust valves

29 Jan 2012 18:42
#500705
I have a question about the tappets again.I'm about to reinstall them,I was wondering could I take a brake caliper honer to clean up the bore so they don't get stuck again? The dimension on the tappets are right on spec but the bore needs to expand a bit. I just don't want to buy a new/used head.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: stuck exhaust valves

29 Jan 2012 19:16
#500718
i would lube the bucket , and bores with 10w30, attach the bucket it to your magnet and slide it in and out of the bores. They should slide in and out freely. If they do that u are good to go.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum