Sleeve to block clearance.
- notaduc
-
Topic Author
- Offline
- User
-

Registered
- Posts: 297
- Thanks: 3
Sleeve to block clearance.
12 Jan 2012 17:12
If someone knows or has a manual, I am looking for the factory tolerance for the block bores.
One of my sleeves slipped out when I was cleaning my block and I want to be sure that the bore is within spec.
Thanks!
One of my sleeves slipped out when I was cleaning my block and I want to be sure that the bore is within spec.
Thanks!
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
- etbike3135
-
- Offline
- User
-

Registered
- Posts: 379
- Thanks: 50
Re: Sleeve to block clearance.
12 Jan 2012 18:21
Ive seen them come out lots of times, especially if your soaking them in really hot water.
Some come out easy and some are in for the long haul. Make sure you dont get dirt under the lip.
Last year I took a block and soaked it then turned all the liners 90' and used it in a motor. No real point in doing I guess I wanted to see if it worked, figured the skirts wore the front and back a bit more. It worked.
Some come out easy and some are in for the long haul. Make sure you dont get dirt under the lip.
Last year I took a block and soaked it then turned all the liners 90' and used it in a motor. No real point in doing I guess I wanted to see if it worked, figured the skirts wore the front and back a bit more. It worked.
1973 Kawasaki Z1
18 years in dragbikes
18 years in dragbikes
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: Sleeve to block clearance.
12 Jan 2012 19:11
etbike is right on the money.
you won't have any problems with it moving because the head gasket and head clamps it,and the counterbore keeps it from being able to fall out the bottom.
i have had a 900 cylinder in my boring bar,boring it,and had the sleeve i was boring fall down onto the table.
i took it out,pushed the sleeve back in(easily) re-clamped it on the sleeve(so it could not fall out again)re-centered it and finished boring it.
i honed it and installed and it has never given us any problems,and it gets whipped hard.
i set cylinder sleeves up with .005 thousandths press fit.
but i have had some older t-rex blocks(big bore,triple exhaust,custom banshee block) that had as little as .0025 press fit.
leon
you won't have any problems with it moving because the head gasket and head clamps it,and the counterbore keeps it from being able to fall out the bottom.
i have had a 900 cylinder in my boring bar,boring it,and had the sleeve i was boring fall down onto the table.
i took it out,pushed the sleeve back in(easily) re-clamped it on the sleeve(so it could not fall out again)re-centered it and finished boring it.
i honed it and installed and it has never given us any problems,and it gets whipped hard.
i set cylinder sleeves up with .005 thousandths press fit.
but i have had some older t-rex blocks(big bore,triple exhaust,custom banshee block) that had as little as .0025 press fit.
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- notaduc
-
Topic Author
- Offline
- User
-

Registered
- Posts: 297
- Thanks: 3
Re: Sleeve to block clearance.
13 Jan 2012 00:40
One slipped out super easy, pretty much fell out. The other three took a little push. Just at hot tank temp, like 160 degrees. I was surprised.
I have them all out now, soda blasted the flanges and the flange seats. Sure made base gasket removal easier. Will resurface the block, cut the flange, and hone the sleeves on the rod hone.
I have them all out now, soda blasted the flanges and the flange seats. Sure made base gasket removal easier. Will resurface the block, cut the flange, and hone the sleeves on the rod hone.
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
