stator seal
- gotakz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 0
stator seal
16 Jan 2012 13:25
Can I just cut and solder/splice the wires to change the seal? Thanks BTW the bike is up and running again.
1976 Kz900-A4
Had a 1985 Gpz750
Had a 1985 Gpz750
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: stator seal
16 Jan 2012 15:13
That's the usual way for the repair/replacement. Make sure the wires are clean before soldering, otherwise you may get a voltage dropping connection. I use Acetone to wipe the wires down before doing this work, but I'd imagine any good electronic spray cleaner will do just as good.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
The following user(s) said Thank You: gotakz
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: stator seal
17 Jan 2012 12:14
I'm not familiar with the seal, but if it is all rubber (no metal ring) you may want to make a slice from the center to the outer edge, slip it over the wires, then superglue the slice back together making the seal whole again. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
The following user(s) said Thank You: gotakz
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: stator seal
17 Jan 2012 12:19
I believe it's this grommet:
www.z1enterprises.com/Alternator-cover-r...Z900-KZ1000-373.aspx
Yes, you have to splice and resolder. I did mine far enough forward that the cut was under the sprocket cover. Replaced the old shielding with new shrink wrap and used high temp rtv on the inside of the grommet.
kzrider.com/forum/2-engine/391055-stator...er-grommet--oil-leak
kzrider.com/forum/4-electrical/144912-bl...ator-grommet-replace
www.kzrider.com/forum/2-engine/42559-alt...-grommet-replacement
www.kzrider.com/forum/2-engine/200118-79...or-wire-seal-leaking
www.kzrider.com/forum/2-engine/126344-stator-cover-oil-leak
kzrider.com/forum/4-electrical/200741-st...rommet-wire-assembly
www.kzrider.com/forum/2-engine/52348-oil-leaking-stator
kzrider.com/forum/4-electrical/32237-rub...tgrommetaquot-sealer
And so on...
Yes, you have to splice and resolder. I did mine far enough forward that the cut was under the sprocket cover. Replaced the old shielding with new shrink wrap and used high temp rtv on the inside of the grommet.
kzrider.com/forum/2-engine/391055-stator...er-grommet--oil-leak
kzrider.com/forum/4-electrical/144912-bl...ator-grommet-replace
www.kzrider.com/forum/2-engine/42559-alt...-grommet-replacement
www.kzrider.com/forum/2-engine/200118-79...or-wire-seal-leaking
www.kzrider.com/forum/2-engine/126344-stator-cover-oil-leak
kzrider.com/forum/4-electrical/200741-st...rommet-wire-assembly
www.kzrider.com/forum/2-engine/52348-oil-leaking-stator
kzrider.com/forum/4-electrical/32237-rub...tgrommetaquot-sealer
And so on...
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: stator seal
17 Jan 2012 19:06
Yup... splice and solder them good.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
The following user(s) said Thank You: gotakz
Please Log in or Create an account to join the conversation.
- DFIGPZ
-
- Offline
- User
-

Registered
- Posts: 615
- Thanks: 121
Re: stator seal
17 Jan 2012 23:48
When I do them i cut the terminals off the ends replace grommet then crimp new terminals on and looks as good as new.
1984 750 Turbo
The following user(s) said Thank You: gotakz
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: stator seal
17 Jan 2012 23:51650ed wrote: I'm not familiar with the seal, but if it is all rubber (no metal ring) you may want to make a slice from the center to the outer edge, slip it over the wires, then superglue the slice back together making the seal whole again. Ed
Have always wanted to try that.
And why not --- as the grommet is relatively inexpensive should another be needed due to leakage through the re-joined area.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
The following user(s) said Thank You: gotakz
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: stator seal
18 Jan 2012 00:24DFIGPZ wrote: When I do them i cut the terminals off the ends replace grommet then crimp new terminals on and looks as good as new.
I wasn't certain I could find terminals the right size to fit the plugs - would be the more elegant solution.
Please Log in or Create an account to join the conversation.
- DFIGPZ
-
- Offline
- User
-

Registered
- Posts: 615
- Thanks: 121
Re: stator seal
19 Jan 2012 00:06You can get them from Jeff at Z1 Enterprises.DoubleDub wrote:DFIGPZ wrote: When I do them i cut the terminals off the ends replace grommet then crimp new terminals on and looks as good as new.
I wasn't certain I could find terminals the right size to fit the plugs - would be the more elegant solution.
1984 750 Turbo
The following user(s) said Thank You: gotakz
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
