cam clearance???
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
cam clearance???
22 Jan 2012 22:06
I am working on clearancing my head to accept a set of psp-3x cams and the question i have is .006 enough clearance between cam and head? I wasnt sure how much room is needed.Thanks
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- APE Jay
-
- User
-

Public
- Thanks: 0
Re: cam clearance???
23 Jan 2012 04:44
Might want a little more. Cams will flex when the motor is running.
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam clearance???
23 Jan 2012 16:46
ok i will, how much do you think will be sufficent? i was just using feeler gauges to check clearance. I wasnt sure how else to check it. Thanks for your help i really appreciate it.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: cam clearance???
23 Jan 2012 17:22
How are you adding relief for the cams? I have never seen anyone explain how this is best accomplished (other than boxing it up and shipping it to someone).
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: cam clearance???
23 Jan 2012 18:51 - 23 Jan 2012 23:26
Higher cam lobe may need additional clearance to avoid hitting against the head and inside of the valve cover.
May add relief to the head (by removing metal from the blue area) and inside surface of the valve cover.
Good Fortune!
May add relief to the head (by removing metal from the blue area) and inside surface of the valve cover.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 23 Jan 2012 23:26 by Patton.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam clearance???
23 Jan 2012 19:01
iam just using a dremel and taking my time and trying to be extra careful
1977 KZ 1000 work in progress
The following user(s) said Thank You: DoubleDub
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: cam clearance???
23 Jan 2012 21:05 - 23 Jan 2012 21:06
dont be afraid to have extra clearance lots of drag bike run .460" lift cams and more. mine are .424". if u cant find a number, go with about .020" to .030”. unless you are running some major size lift, then u may want to check over at dragbike.com for a clearance spec. since there is only so much material there.
do u know your lift ? measure the total lobe height (its largest measurement) then subtract the width. this is your lift.
do u know your lift ? measure the total lobe height (its largest measurement) then subtract the width. this is your lift.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Last edit: 23 Jan 2012 21:06 by mark1122.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam clearance???
23 Jan 2012 23:22
The head is off the bike. The cams are a 418 lift. same as the old andrews 3x cams. I just went with ruffly .026" clearance using feeler guages.I just put the feeler guage in there oiled and roated the cam by hand. If it wouldnt rotate fairly easily i took more out so thats what i mean by ruffly.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: cam clearance???
23 Jan 2012 23:36
Would you mind posting a picture? I'm curious how it looks after you did it. If not, that's cool.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam clearance???
24 Jan 2012 00:52
Iam not all the way done. I gotta buy more dremel bits tomorrow but i got the exhaust side done i will post a picture in a few. But i must remind everyone that this is my first time clearancing a head so its not the best job.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
The following user(s) said Thank You: DoubleDub
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
