i need some good input
- Powerstroke_fan
-
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: i need some good input
29 Jan 2012 19:16
I would try to get your hands on a service manual
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- Dboy78kz1000
-
Topic Author
- Offline
- User
-

Registered
- Posts: 85
- Thanks: 0
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: i need some good input
29 Jan 2012 19:23
Did you remove the little bolts by the number 1 and 4 plugs?
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- Dboy78kz1000
-
Topic Author
- Offline
- User
-

Registered
- Posts: 85
- Thanks: 0
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: i need some good input
29 Jan 2012 19:30
i would read up in the manual and it will tell you alot. but you will need to take the head off the jug. since the bolts are out i would try to lightly tap on the head with a RUBBER mallet but real lightly you dont wanna break the fins on the jug or head.and try to seperate them.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: i need some good input
29 Jan 2012 19:32
and remove the cam chain tensior off the jug also. and then clean everything up real well search in the forums and there is lots of articles on the best way to clean everything up.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- Dboy78kz1000
-
Topic Author
- Offline
- User
-

Registered
- Posts: 85
- Thanks: 0
Re: i need some good input
29 Jan 2012 19:33
i dont understand y i should pull them apart? am i checking for smothing?
Please Log in or Create an account to join the conversation.
- Dboy78kz1000
-
Topic Author
- Offline
- User
-

Registered
- Posts: 85
- Thanks: 0
Re: i need some good input
29 Jan 2012 19:36
i was hoping that my bike was a 1075 but guess not so what do i got to do to get it there?
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: i need some good input
29 Jan 2012 19:41 - 29 Jan 2012 19:42
i think you just need to read the manual. First off if you dont remove it and replace your head gasket it will most likly leak. and if you wanna bore it out its has to come apart.if the idlers are bad it has to come off.
1977 KZ 1000 work in progress
Last edit: 29 Jan 2012 19:42 by Powerstroke_fan.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: i need some good input
29 Jan 2012 20:41
They need to come apart, to clean it properly, then everything will need to be measured to see if it is in spec. u will need the tools shown in the manual. a set of vernier calipers or micrometer are a must. to get to 1075cc, u need to buy pistons and have the sleeves bored out to match there size. tis will cost $600 or $700. then u need a cam chain and all of the idler gears ,$400. then u need to determine if the valves and guides need work. $$$$$ YEEE HAAA !!!! :woohoo:
i hope u are on good terms with the misses. lol :lol:
i hope u are on good terms with the misses. lol :lol:
Attachment 6_150_mm_Digital_vernier_caliper_GAUGE.jpg not found
Attachment 500739.jpg not found
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- Dboy78kz1000
-
Topic Author
- Offline
- User
-

Registered
- Posts: 85
- Thanks: 0
Re: i need some good input
29 Jan 2012 20:56
i would have to do all of that just to get it to a 1075? thats alot $$$$$$ :pinch: my dad has a 78 gs 1000 and its bored to 1375 its runs 9s i wanted to go with a 1375 also but way to much $$$ thanks again guy cus i need all the help i can get
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: i need some good input
29 Jan 2012 21:09
the sad part is that it doesn’t cost that much more for a bigger motor. 1300cc pistons only cost $3 more that 1075 pistons . The problem for u is that u need to get the stock parts healthy first, that means cam chain roller sprockets and the head work. Before u worry about big cc’s.
kzzone.com/
www.z1enterprises.com/Cam-Chain--EK-219H-122-link-1720.aspx
www.z1enterprises.com/Cam-Chain-Idler-As...y--Z1-KZ900-332.aspx
www.z1enterprises.com/Cam-Chain-Idler-Sp...000--Liska-2177.aspx
kzzone.com/
www.z1enterprises.com/Cam-Chain--EK-219H-122-link-1720.aspx
www.z1enterprises.com/Cam-Chain-Idler-As...y--Z1-KZ900-332.aspx
www.z1enterprises.com/Cam-Chain-Idler-Sp...000--Liska-2177.aspx
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
