i need some good input
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: i need some good input
30 Jan 2012 18:52
No eBay APP ID and/or Cert ID defined in Kunena configurationThe rings for stock pistons won't be cheap. Probably close to $200 for a set of four. Plus you may need oversize ones (0.020+ or so) and a hone.
Found this on ebay - one set of +0.020 rings for $63+shipping.
Found this on ebay - one set of +0.020 rings for $63+shipping.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: i need some good input
30 Jan 2012 18:53
Stock rings are $30 a set at Z1Enterprises:
www.z1enterprises.com/70mm-Piston-Rings-...KZ250-KL250-192.aspx
www.z1enterprises.com/70mm-Piston-Rings-...KZ250-KL250-192.aspx
Please Log in or Create an account to join the conversation.
- Dboy78kz1000
-
Topic Author
- Offline
- User
-

Registered
- Posts: 85
- Thanks: 0
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: i need some good input
30 Jan 2012 19:02
No eBay APP ID and/or Cert ID defined in Kunena configurationNot sure I understand the question. But I bet it's answered in the service manual.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: i need some good input
30 Jan 2012 19:07
Also would be helpful if you matched your serial # with those over on zedder.com and updated your signature with year and model so that others could quickly identify which bike you are talking about.
These are the links for the '78 model year serials:
zedder.com/Info/78%20KZ1000-A2.htm
zedder.com/Info/78%20KZ1000-A2A.htm
zedder.com/Info/78%20KZ1000-B2%20LTD.htm
zedder.com/Info/78%20KZ1000-C1%20Police.htm
zedder.com/Info/78%20KZ1000-C1A%20Police.htm
zedder.com/Info/78%20KZ1000-D1%20Z1-R.htm
These are the links for the '78 model year serials:
zedder.com/Info/78%20KZ1000-A2.htm
zedder.com/Info/78%20KZ1000-A2A.htm
zedder.com/Info/78%20KZ1000-B2%20LTD.htm
zedder.com/Info/78%20KZ1000-C1%20Police.htm
zedder.com/Info/78%20KZ1000-C1A%20Police.htm
zedder.com/Info/78%20KZ1000-D1%20Z1-R.htm
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: i need some good input
30 Jan 2012 19:53
i would seperate the head and jug no doubt about it. it would be stupid not to.its already apart.and if you dont you got a 95% chance its gonna leak oil and you will want to check the idlers anyway.and if you gotta get a gasket kit anyway y not seperate?? and you already messed with the cam chain you had to take it off the cams to get the jug and head off so it will need retimed anyway.its not like its any more work in my opinion it would be crazy to put money into something and not check the other parts for wear cuz they do wear.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: i need some good input
30 Jan 2012 22:41 - 30 Jan 2012 23:22
Agreed.
That would be the minimum list - but a leak down prior to tearing it apart would have told you a lot about the condition of the head/valves too. Most of these Kz's need to have a valve job done either due to abuse, lack of adjustment, or just miles.
- Timing components (idlers, rollers, etc for the cam chain)
- Cam chain
- Gaskets
- New head nuts/bolts
- Rings/hone
That would be the minimum list - but a leak down prior to tearing it apart would have told you a lot about the condition of the head/valves too. Most of these Kz's need to have a valve job done either due to abuse, lack of adjustment, or just miles.
Last edit: 30 Jan 2012 23:22 by DoubleDub.
Please Log in or Create an account to join the conversation.
- andy9802gt
-
- Offline
- User
-

Registered
- If it tastes that good, eat it yourself.
- Posts: 695
- Thanks: 19
Re: i need some good input
30 Jan 2012 23:13
Before you commit to anything take the block and pistons to the machine shop and have them measured to make sure they are within limits and the proper piston to bore clearance can be achieved, also ask them if you can get away with honing the bores if you are unsure. From the picture you put up on page 1, the exhaust valve in #4 doesn't look seated and #3 is hard to tell with the shadow and the oil all over in there leading me to think a valve job is in order. Otherwise I agree 100% with what DD and the others have said. Unless your uncle says that the cam chain has very few miles on it you should go on and split the cases and replace it because like mark said, if you don't and it fails your motor is going to be junk. Just know that the $500 you have is only gonna get you about half way back together.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: i need some good input
30 Jan 2012 23:54
If a new cam chain is in order, couldnt you just get one with a master link? I would think splitting the cases is alot of work if you could just fish a new one in.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: i need some good input
31 Jan 2012 00:34
That's another one of those flame war topics. Many guys won't do it, others will in a heartbeat.
Please Log in or Create an account to join the conversation.
- andy9802gt
-
- Offline
- User
-

Registered
- If it tastes that good, eat it yourself.
- Posts: 695
- Thanks: 19
Re: i need some good input
31 Jan 2012 06:25Powerstroke_fan wrote: If a new cam chain is in order, couldnt you just get one with a master link? I would think splitting the cases is alot of work if you could just fish a new one in.
It's alot of work when the engine is still in the bike. Since he already has it torn down 27 more bolts doesn't seem like a big enough road block to not just put a one piece chain on. Plus it lets you replace the o rings between the case halves, clean the oil pump and check its tolerance, and get a real good look at the tranny.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
Please Log in or Create an account to join the conversation.
- andy9802gt
-
- Offline
- User
-

Registered
- If it tastes that good, eat it yourself.
- Posts: 695
- Thanks: 19
Re: i need some good input
31 Jan 2012 06:28
It's early so forgive me if this has already been said, check the end play on the crank before you tear it down any further and check the rods the way it shows you in the manual, they're probably okay but better safe than sorry.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
