Cleaning motor for paint

  • wilsow4
  • wilsow4's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Cleaning motor for paint

05 Feb 2012 18:26
#502274
hey guys,

im new to the forum but i've been doing a lot of reading lately. I have completely disassembled my 1980 kz650 and have moved on to breaking down the motor. I was reading about soda blasting and wanted to soda blast each component of the engine separately. If i do this, should I worry about scoring the gasket surfaces and the cylinders, etc.? And when I go to remove all the old gasket material, i've also read a soft wire brush or a 3m light abrasive pad on a 1/4" air grinder works well.

and also, just in case i dont get to re-assembling the motor straight away, is there a certain oil that i should spray everything with to prevent rust/corrosion?

Thanks guys,
Wes.

Please Log in or Create an account to join the conversation.

  • 750steve
  • 750steve's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 584
  • Thanks: 3

Re: Cleaning motor for paint

05 Feb 2012 20:32
#502300
If you're cleaning each component seperately i'd take a look at vapour blasting (thats what its called in the UK anyway). Its a water & glass bead solution blasted under pressure, results are amazing & it wont harm gasket surfaces, ordinary masking tape (painters tape) is enough to sheild a surface too.



Vapour blasting – also known as wet blasting – uses a fine glass bead suspended in water at a ratio of approximately 1 part bead to 9 parts water.



This slurry is then accelerated by compressed air to provide a gentle, but thorough cleaning, leaving a satin shine without damage to the component.



Unlike bead blasting it will not peen the surface. For masking purposes all that is required is domestic masking tape. The gentle nature of the blast will not penetrate.



Engine cases can be cleaned inside and out. Bearing and gasket surfaces are unharmed.



The system is designed for the cleaning of aluminium, titanium, magnesium and brass etc.



Whilst there is a degreasing element to the cleaning, heavily soiled components will require cleaning before treatment. Paint and anodising will also have to be removed.



Being water based, any item that rusts will oxidise immediately. Any items containing steel should be stripped. Those that cannot will have the studs or drum brake surfaces will be chemically treated after blasting. THE ONUS IS ON THE CUSTOMER TO ENSURE THAT BRAKE SURFACES ARE THROUGHLY DEGREASED BEFORE USE.



This is a parts treatment system. Glass bead, by its nature, penetrates the component and will require a thorough washing to ensure it is removed. Once again, whilst we will wash all parts before return, THE ONUS IS ON THE CUSTOMER TO ENSURE THAT ALL PARTS ARE FREE OF ABRASIVE BEFORE REASSEMBLY.


Advantages of Vapour Blasting:-
Quality
1) Maintaining a metal component in a stable high quality because of batch processing.
2) Enables creating granular crystal.
3) A surface of metal component becomes satin finished surface.
Environment
1) A physical cleaning method without using ozone depleting substance
2) Relatively little rinse water or chemicals, consequently little drainage.

07 ZX6R Race Bike
1977 Z750 B2 Twin
1976 Z650 B1

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Cleaning motor for paint

06 Feb 2012 00:13
#502332
Hey Wes. Welcome to the forum. I just joined the forum last summer after buying an old KZ and am currently doing a rebuild. I did the same thing by taking it all apart, engine and all. The guys on here really now their stuff and are so helpful.

As far as getting old gasket material off, that was what took me the most time on my engine. There were guys who said gasket remover works best, or trying a razor blade (careful not to scratch up the surface, the light abrasive pads were also suggested, but I found my best luck was using the 3M Roloc bristle disk. They work like a charm and leave the surface clean and unharmed.

You might want to check it out:
solutions.3m.com/wps/portal/3M/en_US/Man...PWS904gl2XQ8GNGCPLbl
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • notaduc
  • notaduc's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 297
  • Thanks: 3

Re: Cleaning motor for paint

06 Feb 2012 01:36
#502339
The 3m roloc pads will harm your gasket surface. I work in an automotive machine shop and we see it all the time. I know that these are supposed to be made for this but if you saw a head that was hit with these after a pass on the resurfacer you would understand. I couldnt believe it.

Soda blasting on the other hand should not, I/we remove the chunks of gasket with a scraper(goodson super scraper is amazing) and or razor, and blast the rest.
1980 (mostly) KZ1000

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Cleaning motor for paint

11 Feb 2012 16:10
#503350
I have heard from many others on this forum and know also from personal experience that the roloc pads make a tough job so much easier. If there were to be any scratches on the gasket surface (which I have never seen with my bare eyes or felt with my fingers on the smooth surface) then they must not have any effect on the seal.

It is up to you if you want to try it. I did (as many others on this forum) and had no problems or harsh effect from its use. I sprayed permatex gasket sealant on both sides of gaskets before applying the gaskets to the surface. No leaks or problems.
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • wilsow4
  • wilsow4's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Re: Cleaning motor for paint

12 Feb 2012 17:10
#503498
thanks everyone for the help. I ended up getting the scotch brite roloc disks. worked great! only took a few minutes to remove all of the gasket material. Just have to figure something else out for the spots in between the cylinder sleeves. I'm also gonna put this in a new thread, but what do you guys use for assembly lube when re-assembling a motor?

Wes

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum