Gasket removal
- busted knuckle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 1
Gasket removal
09 Feb 2012 23:02
I have been using a razor blade to remove the leftover gaskets on my engine casing. I know I have caused small scratches on the casing along the gasket line. I have recentenly heard that those small scratches can cause vacum and seal issues. Is this true? Is there anything that I can do to still get a seal?
1979 kz 750 b4
Please Log in or Create an account to join the conversation.
- notaduc
-
- Offline
- User
-

Registered
- Posts: 297
- Thanks: 3
Re: Gasket removal
10 Feb 2012 00:29
Which gasket?
Really depends on the scratch... Small scratch is subjective.
Really depends on the scratch... Small scratch is subjective.
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Gasket removal
10 Feb 2012 00:43
I like using a sharpened piece of Lexan or Plexiglass to remove old gaskets. Tried any of the spray on gasket removers?
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Gasket removal
10 Feb 2012 05:34If you're like me, you'd worry about that too much. So, when I did my rebuild, I sealed them with permatext Ultra-Black Hi-temp gasket sealer. Works great, easy to remove if you have to. BTW, it seals a lot more than tiny scratches...... I had some deep gouges in a couple of places, the old gaskets on mine were murder to get off.busted knuckle wrote: I have been using a razor blade to remove the leftover gaskets on my engine casing. I know I have caused small scratches on the casing along the gasket line. I have recentenly heard that those small scratches can cause vacum and seal issues. Is this true? Is there anything that I can do to still get a seal?
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Gasket removal
10 Feb 2012 05:36Yeah, and brake fluid and penetrating oil and every other chemical I could think of. I think the factory sealed a couple of mine (like the base gasket) with something like 3-bond and it absolutely is invulnerable to removers.MFolks wrote: I like using a sharpened piece of Lexan or Plexiglass to remove old gaskets. Tried any of the spray on gasket removers?
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Gasket removal
10 Feb 2012 05:383-bond is typically used to seal engine case halves or any other parts rarely separated. It seals very well, resists solvents but is very hard to remove.busted knuckle wrote: I have been using a razor blade to remove the leftover gaskets on my engine casing.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- ready2ryde1985
-
- Offline
- User
-

Registered
- got to love these kzs
- Posts: 467
- Thanks: 4
Re: Gasket removal
10 Feb 2012 11:29
Tryed to look up this new tool I have just recently tryed. 
To no luck. I know that scraping gaskets is everyones favorite passtime but I found a tool that makes it a breaze.
At sears they sell a abrasive tool that is the $hitttt
it is a disc with abrasive fingers . they are like 5 bucks
I did a 4.3 intake gasket and some others water pump and exaust
any way I got a nice finish and will never use any kind of scraper agen
just wanted to pass on my experiance
To no luck. I know that scraping gaskets is everyones favorite passtime but I found a tool that makes it a breaze.
At sears they sell a abrasive tool that is the $hitttt
it is a disc with abrasive fingers . they are like 5 bucks
I did a 4.3 intake gasket and some others water pump and exaust
any way I got a nice finish and will never use any kind of scraper agen
just wanted to pass on my experiance
84 kz 700 a1
82 kz550 ltd
82 kz550 ltd
Please Log in or Create an account to join the conversation.
- busted knuckle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 1
Re: Gasket removal
10 Feb 2012 11:33
The liquid gasket on the crankcase was actually almost non exsistant but the base gasket is holding on for dear life. Thank you for all of the advice from everyone. I will be going to the store to pick up an abrasive tool and a can of gasket remover and gasket sealer a little later on after i finish cleaning everything and spec-ing out the gears and replacing chains.
1979 kz 750 b4
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Gasket removal
10 Feb 2012 17:19On mine, the sealer used by the factory on the base gasket was so strong, I thought I would never get the cylinder off. I made a pry tool out of a tire iron that finally got it apart. The gasket actually tore apart in the center with one side staying bonded to each surface.busted knuckle wrote: The liquid gasket on the crankcase was actually almost non exsistant but the base gasket is holding on for dear life. .
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- Kidkawie
-
- Offline
- User
-

Registered
- I bleed premix
- Posts: 1924
- Thanks: 246
Re: Gasket removal
10 Feb 2012 18:40
Those 3M discs are called Rolock Bristle Discs. I've removed hundreds of gaskets so I'm like a surgeon with a regular Rolock disc.
If you're worried about the scratches, just gently smooth them out with some 400 emery cloth and apply Permatex (NOT silicone) gasket adhesive to both the gasket and mating surface. The permatex comes in a spray can or a small brush bottle.
If you're worried about the scratches, just gently smooth them out with some 400 emery cloth and apply Permatex (NOT silicone) gasket adhesive to both the gasket and mating surface. The permatex comes in a spray can or a small brush bottle.
1975 Z1 900
1994 KX250 Supermoto
2004 KX125
1994 KX250 Supermoto
2004 KX125
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: Gasket removal
10 Feb 2012 20:37
If you have an air compressor, pick up a right angle die grinder and a gasket tool like these at harbor freight. Different pads for different uses. Saves ton's of time and does a beautiful job.
Gasket Removal Pads
Gasket Removal Pads
Larry C.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
