Compression difference in one cylinder - 82 550
- apbling
-
Topic Author
- Offline
- User
-

Registered
- Posts: 999
- Thanks: 12
Compression difference in one cylinder - 82 550
11 Feb 2012 10:40
Hello All,
A quick recap on my 82 550's last couple years of life...
1. Holed #2 piston due to major stupidity and carb issues.
2. Replaced #2 piston, rings, valve job and honed sleeve.
3. Current compression is 130ish, whereas 1,3,4 are 150ish.
4. Added new 2.2 ohm dyna coils
5. Fought with various carb issues since.
Now I think I for the most part have gotten 90% of the quirks figured out with my bike. The main issue I am currently having is it has no power to pull from a stop. I've checked and lubed the timing advance. I did have to replace my carbs with a parts set (don't ask...), so I still think even though I've cleaned them tons of times, thats still my issue.
Ok, now to my question. Since #2 cylinder has very little miles on it since being rebuilt, it's compression is 20 lbs or so less than the others. Now, I'm *hoping* that once I get some time on it she'll work in a bit and it'll climb up a few psi. But, would having this one cylinder a little weaker cause much issue with running? When balancing the carbs I also tried to run that carb just a hair lower vacuum to help it out a bit. I'm just starting to worry that my issues aren't carb related, but rather when I go to take off from a stop, I load the motor up some, #2 stops firing and hence my issues. Once I get the RPM's up she pulls hard, right to 90+ mph.
Let me also put a disclaimer out there... I haven't ridden this cold blooded beast in nearly 4 yrs due to this piston issue and have been riding newer, less cold blooded bikes, so it may be I'm just not used to how cold blooded this bike always was...
A quick recap on my 82 550's last couple years of life...
1. Holed #2 piston due to major stupidity and carb issues.
2. Replaced #2 piston, rings, valve job and honed sleeve.
3. Current compression is 130ish, whereas 1,3,4 are 150ish.
4. Added new 2.2 ohm dyna coils
5. Fought with various carb issues since.
Now I think I for the most part have gotten 90% of the quirks figured out with my bike. The main issue I am currently having is it has no power to pull from a stop. I've checked and lubed the timing advance. I did have to replace my carbs with a parts set (don't ask...), so I still think even though I've cleaned them tons of times, thats still my issue.
Ok, now to my question. Since #2 cylinder has very little miles on it since being rebuilt, it's compression is 20 lbs or so less than the others. Now, I'm *hoping* that once I get some time on it she'll work in a bit and it'll climb up a few psi. But, would having this one cylinder a little weaker cause much issue with running? When balancing the carbs I also tried to run that carb just a hair lower vacuum to help it out a bit. I'm just starting to worry that my issues aren't carb related, but rather when I go to take off from a stop, I load the motor up some, #2 stops firing and hence my issues. Once I get the RPM's up she pulls hard, right to 90+ mph.
Let me also put a disclaimer out there... I haven't ridden this cold blooded beast in nearly 4 yrs due to this piston issue and have been riding newer, less cold blooded bikes, so it may be I'm just not used to how cold blooded this bike always was...
Please Log in or Create an account to join the conversation.
- apbling
-
Topic Author
- Offline
- User
-

Registered
- Posts: 999
- Thanks: 12
Re: Compression difference in one cylinder - 82 550
11 Feb 2012 11:15
Forgot to mention, stock jetting, stock airbox, stock pipes.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Compression difference in one cylinder - 82 550
11 Feb 2012 16:17I think being able to get to 90 means that cyclinder must be able to pull pretty well. IMHO, it sounds like a carb problem or vacuum leak maybe.apbling wrote: Hello All,
The main issue I am currently having is it has no power to pull from a stop.
Once I get the RPM's up she pulls hard, right to 90+ mph.
Are the fuel levels set by clear tube?
Check all diaphragms for holes or slits?
Check for leaks at intake manifolds?
Valve clearanaces checked?
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- apbling
-
Topic Author
- Offline
- User
-

Registered
- Posts: 999
- Thanks: 12
Re: Compression difference in one cylinder - 82 550
11 Feb 2012 16:36
Thanks for the reply.
Fuel levels have been a battle, but I think I do have them set. BUT, when it comes out from winter hibernation I was going to devote time to check them again. and again.
Float level was one contributing factor when I blew #2... A rebuild needle snuck it's way in without my knowledge (it was a hair longer, hence lower float level).
No diaphragms. TK22's, mechanical slide, thank god.
Dropped $90 on intake manifolds 2 years ago and used fancy gasket material to seal 'em up. Contributing factor #2 to blowing up #2 piston. Not only did it have a low float level, #2's manifold had a crack underneath, hidden from view.
Clearances checked.
Fuel levels have been a battle, but I think I do have them set. BUT, when it comes out from winter hibernation I was going to devote time to check them again. and again.
No diaphragms. TK22's, mechanical slide, thank god.
Dropped $90 on intake manifolds 2 years ago and used fancy gasket material to seal 'em up. Contributing factor #2 to blowing up #2 piston. Not only did it have a low float level, #2's manifold had a crack underneath, hidden from view.
Clearances checked.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Compression difference in one cylinder - 82 550
12 Feb 2012 00:33 - 12 Feb 2012 00:37
It sounds like a pilot jet problem. The pilots handle all the operation for the first 1/4 throttle opening. At wide open throttle, it's all main jets and it sounds like you have no problem there.
Stumbling offline is usually pilot jet but can be caused by low fuel level in bowl. Mine are super critical to fuel level. Even one mm too high and it ran like crap.
Stumbling offline is usually pilot jet but can be caused by low fuel level in bowl. Mine are super critical to fuel level. Even one mm too high and it ran like crap.
1979 KZ-750 Twin
Last edit: 12 Feb 2012 00:37 by bountyhunter.
Please Log in or Create an account to join the conversation.
- apbling
-
Topic Author
- Offline
- User
-

Registered
- Posts: 999
- Thanks: 12
Re: Compression difference in one cylinder - 82 550
12 Feb 2012 17:23
I bet. On a twin I'm guessing you get a cylinder acting funny you know real fast!
I can deal with a pilot issue. All the passages seemed to blow air/cleaner every direction, but I'll keep at it... and messing with the floats. My worry is it's related to that cylinder compression...like maybe it doesn't have the vacuum "pull" that the others have, thus it's having issues. Although, 130 psi I think is still above the recommended rebuild limit...But going with what you said, at WOT it's pulling through the mains, which is more of a direct shot from bowl to throught, whereas at idle and just off it has to snake all through the carb, and if the cylinder is wimpy, maybe it can't do it...
I can deal with a pilot issue. All the passages seemed to blow air/cleaner every direction, but I'll keep at it... and messing with the floats. My worry is it's related to that cylinder compression...like maybe it doesn't have the vacuum "pull" that the others have, thus it's having issues. Although, 130 psi I think is still above the recommended rebuild limit...But going with what you said, at WOT it's pulling through the mains, which is more of a direct shot from bowl to throught, whereas at idle and just off it has to snake all through the carb, and if the cylinder is wimpy, maybe it can't do it...
Please Log in or Create an account to join the conversation.
- apbling
-
Topic Author
- Offline
- User
-

Registered
- Posts: 999
- Thanks: 12
Re: Compression difference in one cylinder - 82 550
12 Feb 2012 17:25
Forgot to mention the float issues...Not only did I have a different length needle sneak it's way in a while back, but once I put the carbs on the bike, measured the floats. Say, for instance, #4 carb was low. So I took it out, adjusted it (yes, the correct direction, so I should have gotten higher fuel level) and the SOB showed a lower level! Slap on the carb bowl with the screwdriver handle and suddenly it fills up. Touchy little things...
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Compression difference in one cylinder - 82 550
12 Feb 2012 22:41Are you measuring the actual fuel level with a clear tube?apbling wrote: Forgot to mention the float issues...Not only did I have a different length needle sneak it's way in a while back, but once I put the carbs on the bike, measured the floats. Say, for instance, #4 carb was low. So I took it out, adjusted it (yes, the correct direction, so I should have gotten higher fuel level) and the SOB showed a lower level! Slap on the carb bowl with the screwdriver handle and suddenly it fills up. Touchy little things...
If not, you can forget about ever getting it right.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- apbling
-
Topic Author
- Offline
- User
-

Registered
- Posts: 999
- Thanks: 12
Re: Compression difference in one cylinder - 82 550
12 Feb 2012 23:26
yep, clear tube attached to drain nipple.
Please Log in or Create an account to join the conversation.
- roy-b-boy-b
-
- Offline
- User
-

Registered
- Posts: 3245
- Thanks: 103
Re: Compression difference in one cylinder - 82 550
13 Feb 2012 00:43
My bike acted like that the last time I reassembled it before the meet in Ohio. Drove me nuts. My problem was loose intake boots. When I had the rpms up I guess it pulled the boots in for a good seal.
Have you checked the spark plug cap and the end of the wire where it connects on the low compression cylinder?
Try swapping the one out with one you are sure of.
I know things like this drive you crazy. You are just going to have to do diffrent things one at a time until something gives you a clue. Roy
Have you checked the spark plug cap and the end of the wire where it connects on the low compression cylinder?
Try swapping the one out with one you are sure of.
I know things like this drive you crazy. You are just going to have to do diffrent things one at a time until something gives you a clue. Roy
1979 LTD Street Fighter.1977 KZ1000
Please Log in or Create an account to join the conversation.
- apbling
-
Topic Author
- Offline
- User
-

Registered
- Posts: 999
- Thanks: 12
Re: Compression difference in one cylinder - 82 550
13 Feb 2012 01:00
Now that you mention it, the plugs aren't brand new...I'll swap those in when I try it. I have the dyna 2.2 ohm coils and their wires, with no resistor cap. I don't have resistor plugs either, so I even thought that may be an issue???
I'll take another peek at those boots...
What drives me even more crazy is I have a few months to think about this before it gets warm again!
I'll take another peek at those boots...
What drives me even more crazy is I have a few months to think about this before it gets warm again!
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Compression difference in one cylinder - 82 550
13 Feb 2012 06:53If not already done, here's a method to clean the pilot circuit.apbling wrote: ... All the passages seemed to blow air/cleaner every direction....
Especially important to assure that the mixture sprays through the orifice into the carb bore.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
