Assembly Lube

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Assembly Lube

13 Feb 2012 19:24
#503792
Might want to be careful about the amount of lube with moly used? I've heard one other I trust state that it caused his clutch to start slipping after a rebuild. Might have been a one in one thousand case, though. Who knows.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Assembly Lube

13 Feb 2012 21:52 - 14 Feb 2012 02:10
#503826
DoubleDub wrote: Might want to be careful about the amount of lube with moly used? I've heard one other I trust state that it caused his clutch to start slipping after a rebuild. Might have been a one in one thousand case, though. Who knows.
I would never use moly lube either. If it gets into the oil, it soaks into the clutch fiber material and it's there forever.
1979 KZ-750 Twin
Last edit: 14 Feb 2012 02:10 by bountyhunter.

Please Log in or Create an account to join the conversation.

  • z1kzonly
  • z1kzonly's Avatar
  • Offline
  • User
  • User
    Registered
  • Sustaining Member
  • Posts: 2815
  • Thanks: 527

Re: Assembly Lube

13 Feb 2012 22:02
#503829
roy-b-boy-b wrote: He uses this 50/50 mix and then he primes his engine with I don't know what. He probably builds 10 engines a season and the each cost over $30,000 and he hasn't had a failure yet.

It was not my intention to put bad info out. I should have asked him his whole procudure. Roy
Hi Roy, You Guy does Pro Mod as in Drag racing Pro Modified 6.5 et quarters or Pro Mod dirt track oval stuff?
Whatever. When he says prime it. Thats when you just spin the oil pump, either electric, belt drive or old regular shaft from the engine. That circulates trhe oil through all the oil galley holes and bearing journals. Makes oil pressure on the gauge.
Just like, when I change my car oil, I always fill the new filter with oil, it takes a lot, and sucks it up for a while, Then I put it on.
Pro Mods Nitrous motor 900 freakin cubic inch's
Blower, alcohol engine, Jim Oddy Motors 520 C I.
Check this engine out!

Livin in "CheektaVegas, NY
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!

Please Log in or Create an account to join the conversation.

  • z1kzonly
  • z1kzonly's Avatar
  • Offline
  • User
  • User
    Registered
  • Sustaining Member
  • Posts: 2815
  • Thanks: 527

Re: Assembly Lube

13 Feb 2012 22:04
#503830
I just used this picture. Pro Modified
But, It is 904 Cubic Inches! 900 freakin Cubic Inchs?????
Livin in "CheektaVegas, NY
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: Assembly Lube

13 Feb 2012 22:56
#503850
Torco MPZ is what I use.
Larry C.
The following user(s) said Thank You: DoubleDub

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: Assembly Lube

13 Feb 2012 22:59
#503851
elfmagic17 wrote: I use Lubriplate on every engine I build, never had a problem. Knocked a hole in a oilpan on my Monza awhile after a build and pulled a main and a ron cap and look at it to check how they looked, and they looked like brand new bearings. Won't use anything else. But I'm sure most other lubes do a great job. The most important time is initial start up till you get the oil circulating. GM Engine Oil Supplement Is also very good stuff. ( paceperformance.com/i-6485869-88862586-g...mbly-lube-16-oz.html )

I've used lots of Lubriplate. It's a great lube for cam tower bolts also.
Larry C.

Please Log in or Create an account to join the conversation.

  • roy-b-boy-b
  • roy-b-boy-b's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3245
  • Thanks: 103

Re: Assembly Lube

14 Feb 2012 00:48 - 14 Feb 2012 00:51
#503903
We might be straying from the subject. My friend won best engineered car at the million dollar race in Memphis twice.



[IMG


smg.photobucket.com/albums/v245/roy-b-boy-b/Hot%20Rods/
1979 LTD Street Fighter.1977 KZ1000
Last edit: 14 Feb 2012 00:51 by roy-b-boy-b.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum