lash measurement ?
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
lash measurement ?
15 Feb 2012 01:00
I keep getting different measurements with the non- wire feeler guages. Do I have to take my springs out and measure them? The picture in the haynes has the lobe pointing directly away from the center of the opposite cam shaft - the file base has a description suggesting the lobe should point away from the bucket. I have shim under bucket. I have brought the compressor inside to warm it up to do a leak down test now that I have the carbs and exhaust off. I have cleaned and fitted my new rings to my ebay jugs and pistons. I'll listen to the leak down test to determine if I'll do the valve lapping.
Please Log in or Create an account to join the conversation.
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
Re: lash measurement ?
15 Feb 2012 01:15
I'll be doing the leak down cold - will that be useful?
lobe opposite:
1 2 3 4
in.15 .1 .13 .04
ex.18 .08 .13 .08
lobe horizontal:
in.18 .1 .13 .13
ex.18 .13 .18 .05
lobe opposite:
1 2 3 4
in.15 .1 .13 .04
ex.18 .08 .13 .08
lobe horizontal:
in.18 .1 .13 .13
ex.18 .13 .18 .05
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: lash measurement ?
15 Feb 2012 02:14 - 15 Feb 2012 02:17
Check clearance with the cam lobe pointed directly away from the valve. Also, don't reverse direction so the cam chain stays tight.
1979 KZ-750 Twin
Last edit: 15 Feb 2012 02:17 by bountyhunter.
Please Log in or Create an account to join the conversation.
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
Re: lash measurement ?
15 Feb 2012 02:22
anyone have a clue why I get such wildly different measurements? from the various lobe orientations
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: lash measurement ?
15 Feb 2012 09:48
Do you know if they are stock cams? Maybe some of the ramps to and from the lobes are not accurately ground. Or (unlikely but possible) could the cam bearings be a little worn or the cam caps be lose?
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- RonKZ650
-
- Offline
- User
-

Registered
- Posts: 3719
- Thanks: 252
Re: lash measurement ?
15 Feb 2012 12:57
They will always measure different at different points of rotation.
There are different ways to accomplish the same thing here. The general procedure accepted and pretty much outlined in the manuals involves turning the engine over to a specific point of rotation, then digging into your stash of feelers and measure the exact clearance between each valve bucket and cam lobe at the correct point of rotation. Then remove the cams, swap shims, reinstalll the cams, retime the cams. I learned long, long ago there's an easier way. Takes maybe 5 minutes at most to check all 8 valves.
Start out by getting your feelers, you need a .05mm, .10mm, .15mm and a .20mm. This is all you need for the most part, don't bother checking with more precision than that because it doesn't matter as shims are only available in .05mm increments.
Generally shoot for between .10-.15mm clearance cold. Turn the engine over slowly clockwise with your 17mm socket on the right end of the crank. Do this while constantly trying to insert a .10mm feeler between a bucket and cam lobe. If at any point of rotation a .10mm fits, try a .15mm. If not try a .05mm. This can be done quickly when you get the feel for it. Once you figure the largest feeler in .05mm increment that inserts call that your clearance, so if a .10mm fits and a .15mm doesn't, call .10mm your clearance. Do this for all 8 valves then figure what you've got to change. For example say the 8 valves measured .10, .05, 10, .15 on one cam, you'd see 2 are right where you want them, and one needs a one size larger shim, one needs a one size smaller to bring them all to .10mm. So then you remove your upper camchain idler, unbolt the cam, remove the caps, then carefully keep all chain slack between the cams and the chain tight going down in the engine and carefully move the cam towards the center of the engine, remove one of the valve buckets needing adjustment, retrieve the shim, note the size and obtain your suitable replacement, reinstall, carefully lift the cam back in position keeping chain tight going down in the engine, torque down the camcaps to 7 ft/lb or so and you're done with that cam. Recheck clearances and move to the other cam. One cam at a time, do the way I say and timing will not be fouled up.
There are different ways to accomplish the same thing here. The general procedure accepted and pretty much outlined in the manuals involves turning the engine over to a specific point of rotation, then digging into your stash of feelers and measure the exact clearance between each valve bucket and cam lobe at the correct point of rotation. Then remove the cams, swap shims, reinstalll the cams, retime the cams. I learned long, long ago there's an easier way. Takes maybe 5 minutes at most to check all 8 valves.
Start out by getting your feelers, you need a .05mm, .10mm, .15mm and a .20mm. This is all you need for the most part, don't bother checking with more precision than that because it doesn't matter as shims are only available in .05mm increments.
Generally shoot for between .10-.15mm clearance cold. Turn the engine over slowly clockwise with your 17mm socket on the right end of the crank. Do this while constantly trying to insert a .10mm feeler between a bucket and cam lobe. If at any point of rotation a .10mm fits, try a .15mm. If not try a .05mm. This can be done quickly when you get the feel for it. Once you figure the largest feeler in .05mm increment that inserts call that your clearance, so if a .10mm fits and a .15mm doesn't, call .10mm your clearance. Do this for all 8 valves then figure what you've got to change. For example say the 8 valves measured .10, .05, 10, .15 on one cam, you'd see 2 are right where you want them, and one needs a one size larger shim, one needs a one size smaller to bring them all to .10mm. So then you remove your upper camchain idler, unbolt the cam, remove the caps, then carefully keep all chain slack between the cams and the chain tight going down in the engine and carefully move the cam towards the center of the engine, remove one of the valve buckets needing adjustment, retrieve the shim, note the size and obtain your suitable replacement, reinstall, carefully lift the cam back in position keeping chain tight going down in the engine, torque down the camcaps to 7 ft/lb or so and you're done with that cam. Recheck clearances and move to the other cam. One cam at a time, do the way I say and timing will not be fouled up.
321,000 miles on KZ's that I can remember. Not going to see any more.
The following user(s) said Thank You: Patton
Please Log in or Create an account to join the conversation.
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
Re: lash measurement ?
15 Feb 2012 16:25
Thanks, I don't think the cam caps are loose. I've torqued them in the proper order and everything. I don't know what the po has done. I suspect I am a spaz. I'll probably check the spring length for wear even if I don't lap the valve. I'm reassured by some of these suggestions though.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: lash measurement ?
15 Feb 2012 16:39The spring might be shorter (due to wear), or perhaps lost some of its fresh horse sprong, but imo such condition isn't causing the variance in lash readings.joe* wrote: ... I'll probably check the spring length for wear even if I don't lap the valve....
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
