camchain inspection
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
camchain inspection
19 Feb 2012 17:53
Anyone want to try to explain to me why when the tolerances at the bucket /cam lobe are measured in thousandths the cam chain can stretch 4 millimeters?. I have a brand new camchain, the measured difference with the one currently installed is right at one millimetre. Patton was right, after 20,000 the hyvo is still way good.
The haynes says 20 pin length limit is 128.9 - I assume that is end of link to end of link (each link having 2 pins - 20 pins). My 20 pin length is a hair over 125mm.
I'm awful relieved I don't have to take the engine out and split the cases - just new jugs and pistons.
The haynes says 20 pin length limit is 128.9 - I assume that is end of link to end of link (each link having 2 pins - 20 pins). My 20 pin length is a hair over 125mm.
I'm awful relieved I don't have to take the engine out and split the cases - just new jugs and pistons.
Please Log in or Create an account to join the conversation.
- notaduc
-
- Offline
- User
-

Registered
- Posts: 297
- Thanks: 3
Re: camchain inspection
19 Feb 2012 19:03
Why does it matter?
I have seen valve clearances noted in metric and standard. Its still the same measurement, 1mm will always be .0393".
Call the chain stretch tolerance .1574", or the valve clearance .05 - .10mm. Its all the same.
I have seen valve clearances noted in metric and standard. Its still the same measurement, 1mm will always be .0393".
Call the chain stretch tolerance .1574", or the valve clearance .05 - .10mm. Its all the same.
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: camchain inspection
19 Feb 2012 19:09 - 19 Feb 2012 19:25notaduc wrote: Why does it matter?
I have seen valve clearances noted in metric and standard. Its still the same measurement, 1mm will always be .0393".
Call the chain stretch tolerance .1574", or the valve clearance .05 - .10mm. Its all the same.
the clearance between the bucket(shim under) and cam only changes as the valve and seat ware . the clearance gets less. it is not influanced by cam chain stretch.
as the chain stretches your cams timing, will change though. :blink:
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Last edit: 19 Feb 2012 19:25 by mark1122.
Please Log in or Create an account to join the conversation.
- notaduc
-
- Offline
- User
-

Registered
- Posts: 297
- Thanks: 3
Re: camchain inspection
19 Feb 2012 19:12mark1122 wrote:notaduc wrote: Why does it matter?
I have seen valve clearances noted in metric and standard. Its still the same measurement, 1mm will always be .0393".
Call the chain stretch tolerance .1574", or the valve clearance .05 - .10mm. Its all the same.
the clearance between the bucket(shim) and cam only changes as the valve and seat ware . the clearance gets less. it is not influanced by cam chain stretch.
as the chain stretches your cams timing, will change though. :blink:
Hmmm, I didnt infer that he was suggesting that they were linked, just specified in different units.
If so, yea, what he said.
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: camchain inspection
19 Feb 2012 19:13 - 19 Feb 2012 19:14
A "stretched" cam chain has some effect on cam timing, but condition of the cam chain is irrelevant to valve clearances which retain their setting regardless of whether the cam chain is fitted.
Good Fortune!
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 19 Feb 2012 19:14 by Patton.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: camchain inspection
19 Feb 2012 19:24notaduc wrote:mark1122 wrote:notaduc wrote: Why does it matter?
I have seen valve clearances noted in metric and standard. Its still the same measurement, 1mm will always be .0393".
Call the chain stretch tolerance .1574", or the valve clearance .05 - .10mm. Its all the same.
the clearance between the bucket(shim) and cam only changes as the valve and seat ware . the clearance gets less. it is not influanced by cam chain stretch.
as the chain stretches your cams timing, will change though. :blink:
Hmmm, I didnt infer that he was suggesting that they were linked, just specified in different units.
If so, yea, what he said.
sorry duc. i didnt mean to quote u. i clicked quote on the wrong post. lol
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
