head cleaning
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
head cleaning
20 Feb 2012 15:34
Previous post "photos bad cam caps"
The auto machine shop that honed my cylinders has a machine that they clamp the head in and it rotates and the machine has arms that wave around spitting walnut husks. Does this machine have less of a chance of damaging cam caps than the bead blasting I had done 5000 miles ago?
they wanted me to take the valves out, remove end plugs and carb boots before they would work on it.
the cam caps on 4ex 1in and 2 in are bad the rest of the caps and the head are fine.
And again, does anyone care to weigh in on why the marks on my cam caps are not in line with the direction of rotation - crosshatching?
thanks
The auto machine shop that honed my cylinders has a machine that they clamp the head in and it rotates and the machine has arms that wave around spitting walnut husks. Does this machine have less of a chance of damaging cam caps than the bead blasting I had done 5000 miles ago?
they wanted me to take the valves out, remove end plugs and carb boots before they would work on it.
the cam caps on 4ex 1in and 2 in are bad the rest of the caps and the head are fine.
And again, does anyone care to weigh in on why the marks on my cam caps are not in line with the direction of rotation - crosshatching?
thanks
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: head cleaning
20 Feb 2012 16:04 - 20 Feb 2012 16:06
If recalling correctly from the earlier thread, this model is designed with nothing (such as an insert) between the cam cap and the camshaft journal, whereby oil film is the only protection between mating surfaces of the cap and journal.
And concern was expressed about possibility of glass bead residual having damaged the caps and/or journals.
Am just guessing, but seems like the FSM would include a specification for the clearance or tolerance for the "space" between cap and journal. Which would presumably be measured with plastigauge.
Considering the cross-hatching still on the caps, perhaps the parts are still within service limits. If the cross-hatching is factory-produced during manufacture, it could indicate minimal surface wear.
What is the expected benefit of walnut shell blasting in this area?
Good Fortune!
And concern was expressed about possibility of glass bead residual having damaged the caps and/or journals.
Am just guessing, but seems like the FSM would include a specification for the clearance or tolerance for the "space" between cap and journal. Which would presumably be measured with plastigauge.
Considering the cross-hatching still on the caps, perhaps the parts are still within service limits. If the cross-hatching is factory-produced during manufacture, it could indicate minimal surface wear.
What is the expected benefit of walnut shell blasting in this area?
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 20 Feb 2012 16:06 by Patton.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: head cleaning
20 Feb 2012 16:07
I don't believe my head(s) have a cross hatching on them, but I'd have to double check. I'm thinking the head is likely toasted.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: head cleaning
20 Feb 2012 16:14 - 20 Feb 2012 16:15
.
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 20 Feb 2012 16:15 by 650ed.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: head cleaning
20 Feb 2012 16:16 - 20 Feb 2012 16:21joe* wrote: Previous post "photos bad cam caps"
The auto machine shop that honed my cylinders has a machine that they clamp the head in and it rotates and the machine has arms that wave around spitting walnut husks. Does this machine have less of a chance of damaging cam caps than the bead blasting I had done 5000 miles ago?
they wanted me to take the valves out, remove end plugs and carb boots before they would work on it.
the cam caps on 4ex 1in and 2 in are bad the rest of the caps and the head are fine.
And again, does anyone care to weigh in on why the marks on my cam caps are not in line with the direction of rotation - crosshatching?
thanks
Walnut blasting, sand blasting, bead blasting. eek; they all can leave stuff behind. Why not just clean it up the old fashioned way - a little polish and a little elbow grease?
Attachment ENGINECLOSEUP.jpg not found
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 20 Feb 2012 16:21 by 650ed.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: head cleaning
20 Feb 2012 17:24Only way is if the cams were moving laterally (end play) as they rotated.joe* wrote:
And again, does anyone care to weigh in on why the marks on my cam caps are not in line with the direction of rotation - crosshatching?
thanks
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: head cleaning
20 Feb 2012 17:26The place that did my cylinder / head had a hot tank that really got mine clean.650ed wrote:joe* wrote: Previous post "photos bad cam caps"
The auto machine shop that honed my cylinders has a machine that they clamp the head in and it rotates and the machine has arms that wave around spitting walnut husks. Does this machine have less of a chance of damaging cam caps than the bead blasting I had done 5000 miles ago?
they wanted me to take the valves out, remove end plugs and carb boots before they would work on it.
the cam caps on 4ex 1in and 2 in are bad the rest of the caps and the head are fine.
And again, does anyone care to weigh in on why the marks on my cam caps are not in line with the direction of rotation - crosshatching?
thanks
Walnut blasting, sand blasting, bead blasting. eek; they all can leave stuff behind. Why not just clean it up the old fashioned way - a little polish and a little elbow grease?
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
Re: head cleaning
20 Feb 2012 17:29
I thought walnut particles would be less abrasive (softer) than bead blasting and if particles were left in the oil passages they wouldn't be as damageing. The cross hatching is only on the three bad cam caps.
I have gotten rid of most of the carbon on the head, I am reluctant to use a tool near the valve seats-I was hopeing $15 on this walnut shell process would keep me from getting my dull glaziers chisel near fragile spots in the interior.
I have gotten rid of most of the carbon on the head, I am reluctant to use a tool near the valve seats-I was hopeing $15 on this walnut shell process would keep me from getting my dull glaziers chisel near fragile spots in the interior.
Please Log in or Create an account to join the conversation.
- joe*
-
Topic Author
- Offline
- User
-

Registered
- '82 KZ750N
- Posts: 42
- Thanks: 0
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: head cleaning
20 Feb 2012 17:53
I'm pretty sure they're something to be concerned about. They'll probably need to be smoothed out and then have clearances checked - hopefully they won't be out of spec.
Please Log in or Create an account to join the conversation.
- bluej58
-
- Offline
- User
-

Registered
- The chrome don't get you home
- Posts: 2474
- Thanks: 507
Re: head cleaning
20 Feb 2012 22:22
That's awesome Ed.
What do you use ?
I spent all day yesterday going back and forth between engine degreaser and Simple Green .
That cut through the grim but I still have to take off the rust scales.
I'm using a red scouring pad and that is working pretty good, but I can't see it ever looking like yours at this rate.
I was thinking about baking soda, but now I think I'd rather have it a little dingy then risk having any trouble.
What do you use ?
I spent all day yesterday going back and forth between engine degreaser and Simple Green .
That cut through the grim but I still have to take off the rust scales.
I'm using a red scouring pad and that is working pretty good, but I can't see it ever looking like yours at this rate.
I was thinking about baking soda, but now I think I'd rather have it a little dingy then risk having any trouble.
78 KZ1000 A2A
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
