sandblasting engine

  • Powerstroke_fan
  • Powerstroke_fan's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1020
  • Thanks: 90

sandblasting engine

20 Feb 2012 18:51
#505301
I was wanting everyone opinion on my bike. After reading another post of possible sandblasting damage, it made me think,so I already sandblasted my head and jug. i used plugs in the oil galleys and intake and exhaust ports, but iam sure some got in the galleys. so my question is i used a parts washer and put the nozzle in all the galleys and let it run thru multiple times. Then i used probally about three cans of brake cleen each on the head and jug, spraying it in the galleys from both directons with the straw and blowing it out with compressed air. until i didnt see any signs of sand or dirt. do you guys think this is sufficent. I have not got it back together and ran it yet. I also wondered about taking the plugs out and leaving the cams out and turning it over with the starter quite a bit to hopefully push and excess out,once its back together. What do you guys think?
1977 KZ 1000 work in progress

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: sandblasting engine

20 Feb 2012 18:54
#505302
I wouldn't want to push it out after assembling, I would focus on getting it out before assembling. Grit in the oil on the crank/rod bearings or cylinders/piston rings can't be good.

Please Log in or Create an account to join the conversation.

  • joe*
  • joe*'s Avatar
  • Offline
  • User
  • User
    Registered
  • '82 KZ750N
  • Posts: 42
  • Thanks: 0

Re: sandblasting engine

20 Feb 2012 19:10
#505304
i was wondering the same thing. I am at the same point in reassembling. I was thinking of starting it with new oil with the pistons and jugs off to clear the bottommost oil gally. I'm assuming oil goes from the pump to the filter - then to the top end.

Please Log in or Create an account to join the conversation.

  • mtkawboy
  • mtkawboy's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 822
  • Thanks: 16

Re: sandblasting engine

20 Feb 2012 19:28
#505306
Im not posative about sand but you can never get the all glass out when you glass bead regardless of how clean you think it is. Personally Id use soda blasting, disolves in water. Your results and opinions may vary
78-KZ1000/1105, 80 KZ1000, 82 Kawasaki GPZ750, 95 Harley Fatboy, 80 Suzuki GS1100ET, 81 GS1100E parts bike, 83 GS1100SD Katana/1394,78 Yamaha XT500, 81 Yamaha XS650, 78 Yamaha XS650E, 48 Whizzer model J motorbike, 71 Honda CT70H, 71 Honda CT70, 81 IT 250 Yamaha,82 Honda XL100S owned

Please Log in or Create an account to join the conversation.

  • Powerstroke_fan
  • Powerstroke_fan's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1020
  • Thanks: 90

Re: sandblasting engine

20 Feb 2012 19:57 - 20 Feb 2012 20:03
#505311
i already did it and cleaned it like stated above i spent alot of time doing that. i was going to try to soak up all the oil i could but i was just thinking as extra protection. but i think it should be all out of there just wanted everyones opnion.And as i read in a previous post if i remember correctly he said it needed cleaned properly. what is considered properly?
1977 KZ 1000 work in progress
Last edit: 20 Feb 2012 20:03 by Powerstroke_fan.

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: sandblasting engine

20 Feb 2012 20:06
#505313
mtkawboy wrote: Im not posative about sand but you can never get the all glass out when you glass bead regardless of how clean you think it is. Personally Id use soda blasting, disolves in water. Your results and opinions may vary

If that was even close to correct then glass beads wouldn't be the most popular way to clean these engines. I think just about every enigine shop glass beads their engines. Soda would be fine but would probably not yield the results you're after. Sand is gonna be difficult to get out of everything since it packs up when you get it wet. Try back flushing the oil galleys to see if you get anything to come out and remember compressed air is you friend, be thorough with your cleaning efforts and you should be okay. Sand isn't popular because it roughens up the surface causing dirt and grime to stick.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • notaduc
  • notaduc's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 297
  • Thanks: 3

Re: sandblasting engine

20 Feb 2012 21:16 - 20 Feb 2012 21:32
#505330
I work at an engine machine shop. We only soda blast engines. We have a glass cabinet, but we never use it on anything that will contact oil, water, or intake air.


Soda does a fantastic job cleaning up oxidation, old gaskets, and anything else, plus you dont have to worry about contaminating the media. Well, that and yea, its water soluble. Plus its amphoteric and neutralizes most thinks that will corrode metal parts.


I honestly wouldnt risk installing any new parts in an engine that had been blasted with sand or glass... Id replace at least the head , you run serious risk of ruining parts and wasting your labor otherwise.

Actually, we do bead blast valves, but that is a different story.
1980 (mostly) KZ1000
Last edit: 20 Feb 2012 21:32 by notaduc.

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: sandblasting engine

20 Feb 2012 21:21
#505332
DoubleDub wrote: I wouldn't want to push it out after assembling, I would focus on getting it out before assembling. Grit in the oil on the crank/rod bearings or cylinders/piston rings can't be good.

Bingo :)
Larry C.

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: sandblasting engine

20 Feb 2012 21:25
#505335
Well here's three places that do it just to back up what I said, redline cycle, pitstop performance and Cavanaugh racing heads. I trust implicitly the opinions of two of them and at least respect the third.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • notaduc
  • notaduc's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 297
  • Thanks: 3

Re: sandblasting engine

20 Feb 2012 21:31
#505339
I cant help but imagine a glass bead running through my newly rebuilt engine thousands of times...
1980 (mostly) KZ1000

Please Log in or Create an account to join the conversation.

  • Powerstroke_fan
  • Powerstroke_fan's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1020
  • Thanks: 90

Re: sandblasting engine

20 Feb 2012 21:37
#505343
ill clean it out again for the third or fourth time for extra assurance. but i think ill take the risk and put it on. and i was thinking of rigging some kind of line on the oil galleys when and if i crank it over and make the oil well as much as possible go into a jug, i would make sure i crank it over plenty??? do you think that would work???
1977 KZ 1000 work in progress

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: sandblasting engine

20 Feb 2012 21:45
#505344
notaduc wrote: I work at an engine machine shop. We only soda blast engines. We have a glass cabinet, but we never use it on anything that will contact oil, water, or intake air.


Soda does a fantastic job cleaning up oxidation, old gaskets, and anything else, plus you dont have to worry about contaminating the media. Well, that and yea, its water soluble. Plus its amphoteric and neutralizes most thinks that will corrode metal parts.


I honestly wouldnt risk installing any new parts in an engine that had been blasted with sand or glass... Id replace at least the head , you run serious risk of ruining parts and wasting your labor otherwise.

Actually, we do bead blast valves, but that is a different story.

I guess since they don't glass bead parts at the shop you sweep at, it shouldn't be done. You may convince the OP that glass beads are bad and that his head can't be voided of any residue from his sandblasting mistake but, I will not bite on your misinformation. My entire engine was glass bead blasted and properly cleaned and then cleaned again. Power stroke, if you believe that your head should be replaced let me know, I'll come pay you scrap value, bring it home, clean it and put it on the shelf for later use.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum