cam degree wheel
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
cam degree wheel
26 Feb 2012 17:00
ok so iam in the process of degreeing in my cams. Iam using the cam degreeing for zombies under the filebase. the question i have is iam not sure how to install the degree wheel. the guide in the filebase isnt specific. it just says to remove the ignition plate. so do i take out the 17mm bolt to bolt the wheel up or what? Iam not sure so thought i better ask. Thanks
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: cam degree wheel
26 Feb 2012 17:56
All you have to do is attach the whel to your crank with the 0degree mark lined up with your case mark, when the piston(#1 mostlikely), is at TDC.
You can pop out the ignition can bolt (not removing 17mm nut), and just run the bolt thru the wheel and back to crank.
Hope this helps.
You can pop out the ignition can bolt (not removing 17mm nut), and just run the bolt thru the wheel and back to crank.
Hope this helps.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: cam degree wheel
26 Feb 2012 18:07
thats right. just get it on the end of the crank.
get the #1 piston at TDC using the timing marks (this just gets things close)and tighten the wheel on the end of the crank.
Next
when u r positive that u r at tdc, using a positive stop method, "NOT" the timing marks. then u align your pointer to 0* on the timing wheel.
get the #1 piston at TDC using the timing marks (this just gets things close)and tighten the wheel on the end of the crank.
Next
when u r positive that u r at tdc, using a positive stop method, "NOT" the timing marks. then u align your pointer to 0* on the timing wheel.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam degree wheel
26 Feb 2012 18:28
so just wedge the 13mm bolt head in the center hole of the wheel??
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- APE Jay
-
- User
-

Public
- Thanks: 0
Re: cam degree wheel
26 Feb 2012 18:36 - 26 Feb 2012 18:37
You must use a positive stop to find true TDC. If you don't, TDC will be off, so all of your other numbers will be off.
If you move the cams based on a false TDC number, you could cause engine damage.
racetoolz.com/
If you move the cams based on a false TDC number, you could cause engine damage.
racetoolz.com/
Last edit: 26 Feb 2012 18:37 by APE Jay.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam degree wheel
26 Feb 2012 19:00
i am just trying to figure out how to mount the wheel on the crank i have been using the cam degree for zombies under filebase. if i remember correctly it says put on tdc with timing marks, mount wheel then move pointer after you find pos. tdc with tdc stop? just not specific on how to mount the wheel??
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: cam degree wheel
26 Feb 2012 19:03 - 26 Feb 2012 19:22
just remove the 13 bolt in the end of the crank and mount the wheel.
omr has the wheel between the 13mm and 17 mm bolts. he uses the 17mm bolt to turn over the motor. i use the rotor bolt(on the oposite side). the reason he says not to turn the motor over with the 13mm bolt is because it is a week bolt and can brake off.
r u clear on how to set tdc with the positive stop tool ??? do u have the tool ?
if not , u can make 1 from an old spark plug.
omr has the wheel between the 13mm and 17 mm bolts. he uses the 17mm bolt to turn over the motor. i use the rotor bolt(on the oposite side). the reason he says not to turn the motor over with the 13mm bolt is because it is a week bolt and can brake off.
r u clear on how to set tdc with the positive stop tool ??? do u have the tool ?
if not , u can make 1 from an old spark plug.
Attachment oil_temp_fit_1_.jpg not found
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Last edit: 26 Feb 2012 19:22 by mark1122.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam degree wheel
26 Feb 2012 19:43 - 26 Feb 2012 19:44
i do have a tdc. i got a complete cam degree kit.i have not done it yet,but i have pre read the text twice and its seems like it should be easy enough. it explains it pretty well,but if i have any questions i will be sure to ask. thanks for everyones help.
1977 KZ 1000 work in progress
Last edit: 26 Feb 2012 19:44 by Powerstroke_fan.
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: cam degree wheel
27 Feb 2012 08:38
Marky, yup!
Page 8 of the write up shows this....
13mm only for degree wheel mounting....
17mm for wrenching crank...
Page 8 of the write up shows this....
13mm only for degree wheel mounting....
17mm for wrenching crank...
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: cam degree wheel
27 Feb 2012 11:00
A couple of things....
1 - Like Jay said, you need a positive stop to find true TDC. If you don't do that, you're wasting your time.
2- If you're going to mount the degree wheel to the same bolt you're turning the engine over with, add another support to the pointer wire. Easy to bump it....there goes accuracy.
Best bet is mount the degree wheel and pointer on one side and turn the engine over with the bolt on the opposite side.
1 - Like Jay said, you need a positive stop to find true TDC. If you don't do that, you're wasting your time.
2- If you're going to mount the degree wheel to the same bolt you're turning the engine over with, add another support to the pointer wire. Easy to bump it....there goes accuracy.
Best bet is mount the degree wheel and pointer on one side and turn the engine over with the bolt on the opposite side.
Larry C.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: cam degree wheel
27 Feb 2012 15:53
thanks for taking the time to write that omr. It has helped me alot. I probally couldnt do it without that. I have a tdc tool and i will make sure i find true tdc. Larry thanks for the pointers. i am learning as i go along so i will add another support, just in case. Thanks everyone and wish me luck. Gonna give it a try in just a little bit.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
