Another cam degree question
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Another cam degree question
01 Mar 2012 20:59
I have finally got my cams degreed in. I have two questions. My spec sheet for my cams says to run 106-107 degrees. Iam at 106.5 on the intake and 107.25 on the exhaust. Is that going to be ok?? The second question i have is, my adj intake sprocket is maxed out against the right side of the slot. My exhaust sprocket is close to center of the slot. But thats what it took to get a 106.5 on the intake sprocket. Is this normal??? Sounds kinda wierd to me. But i triple checked both of them and they read the same each time.Any suggestions??
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Another cam degree question
01 Mar 2012 23:12
Have you checked the clearance from Piston to Valve? If the IN sprocket is against the far side of the slot, are you sure the teeth aren't off one tooth? There are several write ups on all of this. Here is another if you want to read through.
www.sportrider.com/suspension_settings/h..._hands_on/index.html
www.sportrider.com/suspension_settings/h..._hands_on/index.html
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: Another cam degree question
01 Mar 2012 23:52
i counted the links multiple times before i started degreeing. but ill double check tommorrow.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- andy9802gt
-
- Offline
- User
-

Registered
- If it tastes that good, eat it yourself.
- Posts: 695
- Thanks: 19
Re: Another cam degree question
02 Mar 2012 06:21
Sounds like you may be off a tooth. Both mine are pretty much in the center and I'm set at like 107/108.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
The following user(s) said Thank You: spudbudy
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: Another cam degree question
02 Mar 2012 13:08
ok so i counted again and again and it appears iam right on the 28th pin, so iam gonna post some pictures in a min and let everyone see what i got to get a better idea where iam at.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Another cam degree question
02 Mar 2012 13:10
I always found the pin count confusing. I was off the first time as I was starting on the wrong pin.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: Another cam degree question
02 Mar 2012 13:23
i counted just like it said in the manual, first pin after the dot. then 28th pin to dot on intake cam. heres some pictures.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: Another cam degree question
02 Mar 2012 14:20 - 02 Mar 2012 14:24
Photos are sure a chore to download on here..... What's up with that? 
Looks to me like the intake is late.
Looks to me like the intake is late.
Attachment late.jpg not found
Larry C.
Last edit: 02 Mar 2012 14:24 by LarryC.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: Another cam degree question
02 Mar 2012 14:22
i dont know why all the pictures are upside down.
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Another cam degree question
02 Mar 2012 17:09
The Clymer I have wasn't exactly clear on where to start - I was starting one pin late. That might be your case also.
Please Log in or Create an account to join the conversation.
- Powerstroke_fan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1020
- Thanks: 90
Re: Another cam degree question
02 Mar 2012 17:33
the dot on the exhaust cam sprocket faces front even to or just above the top of the head surface. then you dont count the pin that dots on but start on the next one up correct?
1977 KZ 1000 work in progress
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
