Hanging idle
- baldy110
-
Topic Author
- Offline
- User
-

Registered
- Posts: 2272
- Thanks: 512
Hanging idle
10 Mar 2012 21:28
Most of you will probably say this needs to go in the carbs section but it's not the carbs so here goes.
My GPz1100 engine hangs up when idling down. I have BS34's carbs but that is not the problem. I have tried two sets they both do the same thing. There are no vacumn leaks, new manifolds, sealed the manifolds with yamabond #4, the cables are not sticking, the ignition advancer is working correctly.
Here is what I have done
Checked the ignition advance, working properly.
Checked all valve clearance, all within specs.
Checked the intake boots, no leaks all sealing as they should.
Replaced all o-rings in carbs including the shaft seals.
Checked float levels using the clear tube method, all within specs.
Checked the rubber diaphrams, all in very good conditon look brand new.
Synched carbs they are spot on.
Replaced IC ignitor box with a known good one, no change.
Disconnected the throttle cable, no change.
Replaced the idle jets to #40.
Put the #37.6 idle jets back in.
I have ruled out carburation, so with that anyone have any ideas what else it might be?
My GPz1100 engine hangs up when idling down. I have BS34's carbs but that is not the problem. I have tried two sets they both do the same thing. There are no vacumn leaks, new manifolds, sealed the manifolds with yamabond #4, the cables are not sticking, the ignition advancer is working correctly.
Here is what I have done
Checked the ignition advance, working properly.
Checked all valve clearance, all within specs.
Checked the intake boots, no leaks all sealing as they should.
Replaced all o-rings in carbs including the shaft seals.
Checked float levels using the clear tube method, all within specs.
Checked the rubber diaphrams, all in very good conditon look brand new.
Synched carbs they are spot on.
Replaced IC ignitor box with a known good one, no change.
Disconnected the throttle cable, no change.
Replaced the idle jets to #40.
Put the #37.6 idle jets back in.
I have ruled out carburation, so with that anyone have any ideas what else it might be?
Please Log in or Create an account to join the conversation.
- Garn
-
- Offline
- User
-

Registered
- Posts: 265
- Thanks: 13
Re: Hanging idle
11 Mar 2012 20:12
Just need to know what you mean by your title "Hanging Idle" .... Does it not revert to idle speed, but rather, hangs at higher revs? If this is the case I would suspect throttle cables!
RegardZ>
RegardZ>
1 x 73 Z1 (Jaffa), 74 Z1A, 76 Z900-A4
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
Please Log in or Create an account to join the conversation.
- Polar_Bus
-
- Offline
- User
-

Registered
- Posts: 256
- Thanks: 7
Re: Hanging idle
12 Mar 2012 13:29 - 12 Mar 2012 13:31baldy110 wrote: Most of you will probably say this needs to go in the carbs section but it's not the carbs so here goes.
My GPz1100 engine hangs up when idling down. I have BS34's carbs but that is not the problem. I have tried two sets they both do the same thing. There are no vacumn leaks, new manifolds, sealed the manifolds with yamabond #4, the cables are not sticking, the ignition advancer is working correctly.
Here is what I have done
Checked the ignition advance, working properly.
Checked all valve clearance, all within specs.
Checked the intake boots, no leaks all sealing as they should.
Replaced all o-rings in carbs including the shaft seals.
Checked float levels using the clear tube method, all within specs.
Checked the rubber diaphrams, all in very good conditon look brand new.
Synched carbs they are spot on.
Replaced IC ignitor box with a known good one, no change.
Disconnected the throttle cable, no change.
Replaced the idle jets to #40.
Put the #37.6 idle jets back in.
I have ruled out carburation, so with that anyone have any ideas what else it might be?
Does your idle eventually settle down to normal?
A hanging idle is usually a symptom of a lean condition. If your positive you don't have an air leak , it's possible you have a lean midrange. Maybe try shimming or richening your needles ?
Bikes:
'84 GPz1100
'06 HD Fatboy
'84 GPz1100
'06 HD Fatboy
Last edit: 12 Mar 2012 13:31 by Polar_Bus.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
