top end gasket replacement
- TheFlyingFreemole
-
Topic Author
- Offline
- User
-

Registered
- Posts: 87
- Thanks: 8
top end gasket replacement
13 Mar 2012 00:01
I had some leaks in the upper end of my 1000ltd. I looked at the base gasket closely and it showed no sign of leaking, so I only needed to break down to the head gaskets.
Since I have the head pulled...
-Do I have to replace the base cylinder since the head has been pulled? Or is it OK to leave the cylinder jugs on and keep the original non-leaking gasket seal?
-Should I break into the head and replace valve gaskets? Or am I able to just rebuild using new gaskets and be ok to put everything back in original place?
Since I have the head pulled...
-Do I have to replace the base cylinder since the head has been pulled? Or is it OK to leave the cylinder jugs on and keep the original non-leaking gasket seal?
-Should I break into the head and replace valve gaskets? Or am I able to just rebuild using new gaskets and be ok to put everything back in original place?
1977 KZ1000 LTD B1 (needs minor fine tuning)
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: top end gasket replacement
13 Mar 2012 00:17
My rule of thumb tends to be, if I am already this far, what could it hurt to replace them while it's apart.
Not sure if that helps or not.
Not sure if that helps or not.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: top end gasket replacement
13 Mar 2012 00:48TheFlyingFreemole wrote: I had some leaks in the upper end of my 1000ltd. I looked at the base gasket closely and it showed no sign of leaking, so I only needed to break down to the head gaskets.
Since I have the head pulled...
-Do I have to replace the base cylinder since the head has been pulled? Or is it OK to leave the cylinder jugs on and keep the original non-leaking gasket seal?
-Should I break into the head and replace valve gaskets? Or am I able to just rebuild using new gaskets and be ok to put everything back in original place?
Do I have to replace the base cylinder since the head has been pulled? NO.
Or is it OK to leave the cylinder jugs on and keep the original non-leaking gasket seal? YES.
Should I break into the head and replace valve gaskets? Or am I able to just rebuild using new gaskets
Would install new valve cover and head gaskets. And also consider new valve stem seals (viton).
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
The following user(s) said Thank You: TheFlyingFreemole
Please Log in or Create an account to join the conversation.
- roy-b-boy-b
-
- Offline
- User
-

Registered
- Posts: 3245
- Thanks: 103
Re: top end gasket replacement
13 Mar 2012 09:55
I have owned one of my engines 12 years and have pulled the head several times. I have only replaced the base gasket one time when I replaced the jugs. Roy
1979 LTD Street Fighter.1977 KZ1000
Please Log in or Create an account to join the conversation.
- Puffin
-
- Offline
- User
-

Registered
- Posts: 184
- Thanks: 32
Re: top end gasket replacement
14 Mar 2012 15:50TheFlyingFreemole wrote: I had some leaks in the upper end of my 1000ltd. I looked at the base gasket closely and it showed no sign of leaking, so I only needed to break down to the head gaskets.
Since I have the head pulled...
-Do I have to replace the base cylinder since the head has been pulled? Or is it OK to leave the cylinder jugs on and keep the original non-leaking gasket seal?
-Should I break into the head and replace valve gaskets? Or am I able to just rebuild using new gaskets and be ok to put everything back in original place?
Freemole, No need unless you break/disrupt the Cylinder to Block gasket seal. Valve stems seals yes if you have not allready on a recent rebuild
Puffin
KZ1000 J Long Term Owner
KZ1100
KZ1100 Spectre project
KZ1100
KZ1100 Spectre project
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
