Cam cap helicoils...Help with locktight
- KZB2 650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1472
- Thanks: 264
Cam cap helicoils...Help with locktight
20 Mar 2012 12:30
Hey guys finally got the guts up to drill and tap all 16 cam cap holes for helicoils. 6mm 1.0 12mm long.
Things went good and was all ready to start locktighting them in when I noticed there is a high strenghth and a high temp red locktight.
Red High strenghth says its good for 300 degree's while the Red HT is good for 450 but not quite as strong 180 inch lbs vs 230 inch pounds on a 3 eights bolt.
Which do you guys use, I've got things going great up to this point and do want to mess up here. Thanks.
Things went good and was all ready to start locktighting them in when I noticed there is a high strenghth and a high temp red locktight.
Red High strenghth says its good for 300 degree's while the Red HT is good for 450 but not quite as strong 180 inch lbs vs 230 inch pounds on a 3 eights bolt.
Which do you guys use, I've got things going great up to this point and do want to mess up here. Thanks.
1978 KZ650 b-2
700cc Wiseco kit 10 to 1.
1980 KZ750 cam, ape springs, stock clutch/ Barnett springs.
Vance and Hines Header w/ comp baffle and Ape pods, Dyna S and green coils, copper wires.
29MM smooth bores W/ 17.5 pilots, 0-6s and 117.5 main
16/42 gearing X ring chain and alum rear JT sprocket.
700cc Wiseco kit 10 to 1.
1980 KZ750 cam, ape springs, stock clutch/ Barnett springs.
Vance and Hines Header w/ comp baffle and Ape pods, Dyna S and green coils, copper wires.
29MM smooth bores W/ 17.5 pilots, 0-6s and 117.5 main
16/42 gearing X ring chain and alum rear JT sprocket.
Please Log in or Create an account to join the conversation.
- RonKZ650
-
- Offline
- User
-

Registered
- Posts: 3719
- Thanks: 252
Re: Cam cap helicoils...Help with locktight
20 Mar 2012 14:20
No need for any Loctite.
321,000 miles on KZ's that I can remember. Not going to see any more.
Please Log in or Create an account to join the conversation.
- johnbgood
-
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 4
Re: Cam cap helicoils...Help with locktight
20 Mar 2012 18:26
I agree. No loctite required on helicoil.
Johnbgood
Johnbgood
KZ1000P 1991
Please Log in or Create an account to join the conversation.
- z1kzonly
-
- Offline
- User
-

Registered
- Sustaining Member
- Posts: 2815
- Thanks: 527
Re: Cam cap helicoils...Help with locktight
20 Mar 2012 19:11
And, no torque wrench either!
I never used a torque wrench! Always by feel!
Inch pounds/ How many people think they are doing it right, when all of the sudden they just strip that bolt in an instant!
I cut a ratchet off in half 30 yrs ago.
It fits in my palm. I always used sense of feel!
My opinion
I never used a torque wrench! Always by feel!
Inch pounds/ How many people think they are doing it right, when all of the sudden they just strip that bolt in an instant!
I cut a ratchet off in half 30 yrs ago.
It fits in my palm. I always used sense of feel!
My opinion
Livin in "CheektaVegas, NY
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!
Please Log in or Create an account to join the conversation.
- KZB2 650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1472
- Thanks: 264
Re: Cam cap helicoils...Help with locktight
22 Mar 2012 10:00
Thanks guys, I know there's a few guys on here that believe you must loctite em but there's quite a few that say no so.....
To late on the torque wrench, went out and bought a good beam type 0 to 200 inch Lb and a Harbor frieght one too to double check each one. Never stripped one yet doing it for insurance and by the time I check the new old cams and get it bench shimmed I know I'll have em in and out quite a few times.
To late on the torque wrench, went out and bought a good beam type 0 to 200 inch Lb and a Harbor frieght one too to double check each one. Never stripped one yet doing it for insurance and by the time I check the new old cams and get it bench shimmed I know I'll have em in and out quite a few times.
1978 KZ650 b-2
700cc Wiseco kit 10 to 1.
1980 KZ750 cam, ape springs, stock clutch/ Barnett springs.
Vance and Hines Header w/ comp baffle and Ape pods, Dyna S and green coils, copper wires.
29MM smooth bores W/ 17.5 pilots, 0-6s and 117.5 main
16/42 gearing X ring chain and alum rear JT sprocket.
700cc Wiseco kit 10 to 1.
1980 KZ750 cam, ape springs, stock clutch/ Barnett springs.
Vance and Hines Header w/ comp baffle and Ape pods, Dyna S and green coils, copper wires.
29MM smooth bores W/ 17.5 pilots, 0-6s and 117.5 main
16/42 gearing X ring chain and alum rear JT sprocket.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Cam cap helicoils...Help with locktight
22 Mar 2012 10:50
Use the torque wrench. I'm not saying z1kzonly cannot tighten things down properly without one - some folks can, but most folks are not born with that "feel" and end up overtightening, undertightening, or stripping threads before they ever develop that skill. Speaking for myself, I'm positive I cannot tell when I have tightened a bolt to 100 inch pounds +- 2% just by feel; so I rely on torque wrenches for accuracy. They haven't let me down yet - zero stripped threads on my KZ650 in 35 years. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
