Oversized rings?
- WarTiger
-
Topic Author
- Offline
- User
-

Registered
- Don't be scared...CUT IT UP!!!
- Posts: 39
- Thanks: 0
Oversized rings?
22 Mar 2012 19:29
So I got a good deal on a cylinder block on fleabay.....maybe a little too good. I got it in and took a quick look and a quick mic check and it seemed good so I oiled it up and set it aside while I was working on the crankcase. I pulled it out today and in better light i noticed that somebody did a hack honing job on it. I'm going to take it to the machine shop to have them take a look at it, but I fear the damage is done.
I beleive that a thorough professional hone on the cylinders will most likely fix the issue, but I am afraid that it might be out of spec after that. My question is this. Do they make an oversized ring to use on the stock pistons if you have to do a heavy hone or a minimal bore. Of course my first idea was that it was the perfect excuse to go for a big bore kit, but when I priced them I cahnged my mind real quick. At $450 to $600 plus machine shop time, my budget would pretty much be blown, and I still have quite a few things to buy for my build. So any help on the matter would be greatly appreciated. Thanks.
I beleive that a thorough professional hone on the cylinders will most likely fix the issue, but I am afraid that it might be out of spec after that. My question is this. Do they make an oversized ring to use on the stock pistons if you have to do a heavy hone or a minimal bore. Of course my first idea was that it was the perfect excuse to go for a big bore kit, but when I priced them I cahnged my mind real quick. At $450 to $600 plus machine shop time, my budget would pretty much be blown, and I still have quite a few things to buy for my build. So any help on the matter would be greatly appreciated. Thanks.
- Caleb -
82 KZ1000M2 CSR (POS with loads of potential!!)
82 XV750 Custom Cafe (Former POS....potential revealed!!)
82 KZ1000M2 CSR (POS with loads of potential!!)
82 XV750 Custom Cafe (Former POS....potential revealed!!)
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Oversized rings?
22 Mar 2012 19:36
I'd ask these people, as they supposedly can make rings for most any engine:
www.hastingsmfg.com/
www.hastingsmfg.com/
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Oversized rings?
22 Mar 2012 21:03
OE oversize rings are getting near impossible to find. They did make them - check the parts diagrams on Kawasaki.com.
Please Log in or Create an account to join the conversation.
- WarTiger
-
Topic Author
- Offline
- User
-

Registered
- Don't be scared...CUT IT UP!!!
- Posts: 39
- Thanks: 0
Re: Oversized rings?
22 Mar 2012 21:54
Here is a thought. I was looking around at Z1 and saw that pre-81 KZ1000s have a ring size of 70mm. The stock size for mine is 69.5. Could the older model rings be installed on my stock pistons with a bore over of .5mm. Now I am a pretty decent mechanic, but when it comes to figuring out these fine tolerances and machining and such I am totally inexperienced. So if that sounds like a dumb idea, try not to beat me up too bad. Lol.
- Caleb -
82 KZ1000M2 CSR (POS with loads of potential!!)
82 XV750 Custom Cafe (Former POS....potential revealed!!)
82 KZ1000M2 CSR (POS with loads of potential!!)
82 XV750 Custom Cafe (Former POS....potential revealed!!)
Please Log in or Create an account to join the conversation.
- notaduc
-
- Offline
- User
-

Registered
- Posts: 297
- Thanks: 3
Re: Oversized rings?
22 Mar 2012 22:31
feel like this would leave you with inescapable piston slap...
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Oversized rings?
22 Mar 2012 22:43
Yeah, not sure about the I.D. fit of the rings that way - I think they would be too loose on the pistons.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Oversized rings?
22 Mar 2012 22:44
No eBay APP ID and/or Cert ID defined in Kunena configurationOne set - now you just need three more:
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Oversized rings?
22 Mar 2012 22:45
No eBay APP ID and/or Cert ID defined in Kunena configurationSet #2, two to go.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Oversized rings?
22 Mar 2012 22:48
www.ronayers.com/ProductDetails/N/687/SKU/167301
I would give them a call and see if they can actually get them. They might still be available since those are the same as the Police pistons (I think) which were made for a very long time.
I would give them a call and see if they can actually get them. They might still be available since those are the same as the Police pistons (I think) which were made for a very long time.
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: Oversized rings?
23 Mar 2012 11:22
proper cylinder wall to piston clearance is critical for an engine to perform.
as notaduc said once your bore is out of spec for your piston clearance you are going to get excessive piston skirt slap.
slap a skirt against the cylinder wall enough times and it will metal fatigue and break off. :sick:
that gets expensive fast :blush: .
after you have the proper cylinder wall to skirt clearance then you proceed to the rings and make sure they are right.
YOU CANNOT USE OVERSIZE RINGS TO CURE A CYLINDER TO SKIRT CLEARANCE PROBLEM.
it is your money spend it how you wish but remember what i just wrote.
if i were you i would sell the block you bought and find another that can be bored to fit your old pistons and put new rings on your old pistons and set the end gap properly,then you will have an engine that was rebuilt as cheap as possible that you can count on for miles and miles.
thats my .02 fwiw,
leon
as notaduc said once your bore is out of spec for your piston clearance you are going to get excessive piston skirt slap.
slap a skirt against the cylinder wall enough times and it will metal fatigue and break off. :sick:
that gets expensive fast :blush: .
after you have the proper cylinder wall to skirt clearance then you proceed to the rings and make sure they are right.
YOU CANNOT USE OVERSIZE RINGS TO CURE A CYLINDER TO SKIRT CLEARANCE PROBLEM.
it is your money spend it how you wish but remember what i just wrote.
if i were you i would sell the block you bought and find another that can be bored to fit your old pistons and put new rings on your old pistons and set the end gap properly,then you will have an engine that was rebuilt as cheap as possible that you can count on for miles and miles.
thats my .02 fwiw,
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
The following user(s) said Thank You: DoubleDub
Please Log in or Create an account to join the conversation.
- testarossa
-
- Offline
- User
-

Registered
- Attack life, it's only trying to kill you.
- Posts: 3673
- Thanks: 83
Re: Oversized rings?
23 Mar 2012 11:35531blackbanshee wrote: proper cylinder wall to piston clearance is critical for an engine to perform.
as notaduc said once your bore is out of spec for your piston clearance you are going to get excessive piston skirt slap.
slap a skirt against the cylinder wall enough times and it will metal fatigue and break off. :sick:
that gets expensive fast :blush: .
after you have the proper cylinder wall to skirt clearance then you proceed to the rings and make sure they are right.
YOU CANNOT USE OVERSIZE RINGS TO CURE A CYLINDER TO SKIRT CLEARANCE PROBLEM.
it is your money spend it how you wish but remember what i just wrote.
if i were you i would sell the block you bought and find another that can be bored to fit your old pistons and put new rings on your old pistons and set the end gap properly,then you will have an engine that was rebuilt as cheap as possible that you can count on for miles and miles.
thats my .02 fwiw,
leon
I agree with everything that Leon has to say here.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Oversized rings?
23 Mar 2012 15:32
Thanks guys - makes sense to me now that you laid it out there.
So what purpose do oversized rings serve?
So what purpose do oversized rings serve?
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
