All apart, now what....
- BB
-
Topic Author
- Offline
- User
-

Registered
- Posts: 51
- Thanks: 0
All apart, now what....
19 Apr 2012 11:54
Hi Guys,
I am doing a complete rebild of a 1980 KZ1000P. She has 36,000 miles on her, hasnt run in a while. I though I would pull the engine all the way down since I was going this far. Internals all look good, everything so far is within spec, very little wear. I know the cops beat on these bikes, but they were maintained to the book also.
I plan to replace the cam chain and all gears, new rings, gaskets etc.
My question is now that I have it all apart, are there any other parts I should look at/replace?
Thanks for the help, photos below.
I am doing a complete rebild of a 1980 KZ1000P. She has 36,000 miles on her, hasnt run in a while. I though I would pull the engine all the way down since I was going this far. Internals all look good, everything so far is within spec, very little wear. I know the cops beat on these bikes, but they were maintained to the book also.
I plan to replace the cam chain and all gears, new rings, gaskets etc.
My question is now that I have it all apart, are there any other parts I should look at/replace?
Thanks for the help, photos below.
Attachment IMG_0207.JPG not found
Attachment IMG_0214.JPG not found
Attachment IMG_0226_2012-04-19.JPG not found
Attachment IMG_0227.JPG not found
Attachment IMG_0237.JPG not found
Attachment IMG_0247_2012-04-19.JPG not found
Attachment IMG_0246.JPG not found
1980 KZ1000P - The Mistress
2002 R1150GS - Matilda
2002 R1150GS - Matilda
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: All apart, now what....
19 Apr 2012 20:37 - 19 Apr 2012 20:39
Smart Move 
Replace all the ancient cam sprocket idlers with Liska idlers along with that new cam chain.
Not much carbon build up for all those miles. Measure up your bores and pistons. You might just get by with a ball hone and new rings.
Replace all the ancient cam sprocket idlers with Liska idlers along with that new cam chain.
Not much carbon build up for all those miles. Measure up your bores and pistons. You might just get by with a ball hone and new rings.
Larry C.
Last edit: 19 Apr 2012 20:39 by LarryC.
Please Log in or Create an account to join the conversation.
- Chaotic Reason
-
- Offline
- User
-

Registered
- Posts: 384
- Thanks: 15
Re: All apart, now what....
19 Apr 2012 21:16
I'd do the shift shaft seal, and all the oil-rings (oil pump, internal oil passageway, oil filter cover and oil filter), tach drive seal, and valve stem seats. May I also assume that you'll be cleaning the head and lapping the valves? You might want to check your valve guides for any play in them. Just my 2 cents.
Good luck.
Good luck.
Michael
1980 KZ1000 shaft drive
1980 KZ1000 shaft drive
Please Log in or Create an account to join the conversation.
- TomW
-
- Offline
- User
-

Registered
- Keep the blue side up.
- Posts: 502
- Thanks: 52
Re: All apart, now what....
20 Apr 2012 13:27
For sure what everyone else said, plus clean and overhaul the carbs, install APE cylinder studs, check the clutch discs for wear, replace if worn beyond 1/2 the service life, replace all the oil seals and use Viton valve seals, pull the rotor and look at the starter clutch, replace the springs and pins if worn. I've got a once used ball hone I'll lend you to do your cylinders. PM me on that. Polish the cases while you have it apart. Make it look as good as it runs.
'78 KZ1000B2 LTD stock + Vetter Fairing & luggage
'91 ZG1200B5 Voyager XII, stock
'91 ZG1200B5 Voyager XII, stock
Please Log in or Create an account to join the conversation.
- BB
-
Topic Author
- Offline
- User
-

Registered
- Posts: 51
- Thanks: 0
Re: All apart, now what....
23 Apr 2012 17:27
Awesome tips guys, thanks for the advice. I am pretty mechanically minded but this is my first project. Forgive my ignorance but please explain the ball hone process?
TomW - she is all at the powdercoaters, he is blasting everything clean for me and applying a clear wet paint to the engine, powdercoating everything else - she should look beautiful. I cant wait to get the pieces bacj and start assembly.
thanks again for the tips, if I am this deep I dont want to skimp now. Can I get rid of the valve cover tops with the hose connector? Seems like I could just put in plain covers?
TomW - she is all at the powdercoaters, he is blasting everything clean for me and applying a clear wet paint to the engine, powdercoating everything else - she should look beautiful. I cant wait to get the pieces bacj and start assembly.
thanks again for the tips, if I am this deep I dont want to skimp now. Can I get rid of the valve cover tops with the hose connector? Seems like I could just put in plain covers?
1980 KZ1000P - The Mistress
2002 R1150GS - Matilda
2002 R1150GS - Matilda
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: All apart, now what....
23 Apr 2012 17:40 - 23 Apr 2012 17:42
A ball hone isn't as painful as the name sounds. :ohmy: Here's an example:
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 23 Apr 2012 17:42 by 650ed.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
