Poor top end power?

  • LukeMacPU
  • LukeMacPU's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 77
  • Thanks: 1

Poor top end power?

30 Apr 2012 14:15
#518819
Experts, please help me out.

The bike runs pretty good, and pulls hard from 3500 - 6500, but there it really seems to taper off much past that. Seems odd to me, and I didn't notice this before I installed the baffle in my exhaust.

Three questions:

1. Is it normal to be a little flat in the high rpm range?

2. Could adding baffles/re-packing the exhaust contribute?

3. Anything I can do to fix it?
'75 Z1B - work in progress

Please Log in or Create an account to join the conversation.

  • LukeMacPU
  • LukeMacPU's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 77
  • Thanks: 1

Re: Poor top end power?

03 May 2012 07:31
#519518
I'm fairly confident something isn't right at this point, just don't know what. I was having trouble keeping my ignition timing correct so I swapped the points/condensers for an electronic timing plate instead. Timing is dead on the marks.

I guess I'll start by pulling the carbs again. Maybe I've got junk stuck in the jets?

The bike definitely stops pulling hard after about 6500 rpms. Any suggestions? Would a lean condition do that?
'75 Z1B - work in progress

Please Log in or Create an account to join the conversation.

  • jonnybravo
  • jonnybravo's Avatar
  • Offline
  • Banned
  • Banned
    Registered
  • Posts: 518
  • Thanks: 18

Re: Poor top end power?

03 May 2012 07:57
#519519
hows ur valve adjustment

Please Log in or Create an account to join the conversation.

  • LukeMacPU
  • LukeMacPU's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 77
  • Thanks: 1

Re: Poor top end power?

03 May 2012 08:13 - 03 May 2012 08:14
#519520
Valves were adjusted less than 500 miles ago. They were good then, haven't checked since.
'75 Z1B - work in progress
Last edit: 03 May 2012 08:14 by LukeMacPU.

Please Log in or Create an account to join the conversation.

  • zed1015
  • zed1015's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3374
  • Thanks: 2080

Re: Poor top end power?

03 May 2012 08:33 - 03 May 2012 08:42
#519522
LukeMacPU wrote: Experts, please help me out.

The bike runs pretty good, and pulls hard from 3500 - 6500, but there it really seems to taper off much past that. Seems odd to me, and I didn't notice this before I installed the baffle in my exhaust.


Could adding baffles/re-packing the exhaust contribute?

Yes.
It is obvious that if the bike was ok before you installed the baffle then the baffle is causing your problem .
Why now start playing with a totally unrelated areas of the bike and fu*k them up too ?.

Adding the baffle or over packing has created too much back pressure which will restrict engine breathing at higher revs.
The exhaust is restricted allowing gas pressure to build up in the system and choke the engine.

An engine is an air pump and needs a reasonably unrestricted intake and outlet to function.

The higher the revs a higher amount of gas is flowed.
AIR CORRECTOR JETS FOR VM CARBS AND ETHANOL RESISTANT VITON CHOKE PLUNGER SEAL REPLACMENT FOR ALL CLASSIC AND MODERN MOTORCYCLE CARBURETTORS
www.kzrider.com/forum/23-for-sale/611992...lide-mikunis?start=1






Last edit: 03 May 2012 08:42 by zed1015.

Please Log in or Create an account to join the conversation.

  • Street Fighter LTD
  • Street Fighter LTD's Avatar
  • Offline
  • Moderator
  • Moderator
    Registered
  • TURBO, Its Better to be Blown than Injected
  • Posts: 5190
  • Thanks: 2339

Re: Poor top end power?

03 May 2012 08:59
#519528
Pull Baffle, Enjoy Exhaust Sound.

Original owner 78 1000 LTD
Mr Turbo Race Kit, MTC 1075 Turbo pistons by PitStop Performance , Falicon Ultra Lite Super Crank, APE everything. Les Holt @ PDM's Billet Goodies . Frame by Chuck Kurzawa @ Logghe Chassis . Deep sump 5qt oil pan. RIP Bill Hahn

Please Log in or Create an account to join the conversation.

  • LukeMacPU
  • LukeMacPU's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 77
  • Thanks: 1

Re: Poor top end power?

03 May 2012 09:06
#519531
Sounds pretty simple. I guess I'll pull the baffle packing and see what that does.

Best case, my problem is solved. Worst case, I find out that's not it.

Don't know why I didn't think of that.
'75 Z1B - work in progress

Please Log in or Create an account to join the conversation.

  • baldy110
  • baldy110's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 2272
  • Thanks: 512

Re: Poor top end power?

03 May 2012 12:10 - 03 May 2012 12:12
#519562
I'm with ZED1015 on this. It has been my experience that if my bike ran fine and then after working on it it doesn't then what I worked on caused the problem.
Either pull the baffle out or if you want it quieter then go down one size on the main jet.
Last edit: 03 May 2012 12:12 by baldy110.

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Poor top end power?

03 May 2012 14:49
#519593
Running a fuel filter? Check to see if it's clogged too.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • roy-b-boy-b
  • roy-b-boy-b's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3245
  • Thanks: 103

Re: Poor top end power?

03 May 2012 15:41
#519596
At 6000 that bike should pull your head off.

Baffle on jet.

Do you know the jet sizes. What kind of exhaust? Roy
1979 LTD Street Fighter.1977 KZ1000

Please Log in or Create an account to join the conversation.

  • LukeMacPU
  • LukeMacPU's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 77
  • Thanks: 1

Re: Poor top end power?

03 May 2012 15:48 - 03 May 2012 15:50
#519599
roy-b-boy-b wrote: At 6000 that bike should pull your head off.

Baffle on jet.

Do you know the jet sizes. What kind of exhaust? Roy

Don't know the jet sizes, I've not changed them, but could be anything in a bike that's been around since '75. I got a good look at the pilots when I had the carbs off, but not the primaries.

My exhaust is a 4-into-1 of unknown manufacturer. It has roughly a 1.5" straight-through baffle in a megaphone exhaust can. When I got it, there was no packing at all and the baffle, roughly 16" long, was loose inside. I was able to weld it back to the end cap and re-install. Just added packing recently.

It is quieter, but I didn't really expect much change in performance with the straight through design. I'll pull it out and see what I've got. If it gets better, I'll leave it out. If not, I'll pull the carbs off and get back to work starting with checking the primary jet size.

Thanks again for all the help. This site is great!
'75 Z1B - work in progress
Last edit: 03 May 2012 15:50 by LukeMacPU.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Poor top end power?

03 May 2012 17:15
#519617
if it gets better when u remove the packing, u have confirmed the problem. next step would be to solve it. if thats the problem , and u prefer to have the packing in. then u may just have to rejet to get the top end back.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum