Cam End Plugs
- Fastdave61
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Cam End Plugs
07 May 2012 21:25
The cam end plugs keep blowing out of my '80 KZ 1000. Long story short, last fall I did a top end, weather was cold so I only put on 250 miles, bike ran great. This winter I removed the cam cover and adjusted the valves, installed a new gasket and cam end plugs. I added pods and vented the crankcase. First test ride, 2 plugs blew out. Installed new plugs (super glue this time) they blew out within 3 miles. Kind of hard on my Danners. Any tips regarding sealant, ect will be appreciated. Thanks in advance. FD61
1969 BSA A65F Firebird
2004 BMW R1150RT
1980 Kz1000G1
2008 Triumph Tiger 1050
Bemidji, Mn
2004 BMW R1150RT
1980 Kz1000G1
2008 Triumph Tiger 1050
Bemidji, Mn
Please Log in or Create an account to join the conversation.
- Kapahulu
-
- Offline
- User
-

Registered
- Posts: 564
- Thanks: 41
Re: Cam End Plugs
07 May 2012 21:35
Here's a thorough discussion:
www.kzrider.com/forum/2-engine/323919-cam-end-caps
1978 KZ1000, 1976 KZ900, 1975 H2, 1973 H1, 1973 H2, 1978 RD400, 1977 RD400, 1974 RD350
2strokeworld.com
2strokeworld.com
The following user(s) said Thank You: Fastdave61
Please Log in or Create an account to join the conversation.
- Garn
-
- Offline
- User
-

Registered
- Posts: 265
- Thanks: 13
Re: Cam End Plugs
07 May 2012 21:45
FastDave, I think the answer is to....
Make sure the cam end plugs fit and don't protrude too much
Ensure the surfaces are free from oil.
Allow time for sealant to cure, before pulling the cam cover down.
I have seen the Black alloy cam plugs fitted neatly and have been thinking of going with them.
RegardZ
Make sure the cam end plugs fit and don't protrude too much
Ensure the surfaces are free from oil.
Allow time for sealant to cure, before pulling the cam cover down.
I have seen the Black alloy cam plugs fitted neatly and have been thinking of going with them.
RegardZ
1 x 73 Z1 (Jaffa), 74 Z1A, 76 Z900-A4
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
The following user(s) said Thank You: Fastdave61
Please Log in or Create an account to join the conversation.
- Street Fighter LTD
-
- Offline
- Moderator
-

Registered
- TURBO, Its Better to be Blown than Injected
- Posts: 5190
- Thanks: 2339
Re: Cam End Plugs
07 May 2012 22:17
Go Aluminum and no issues for 30 years
Check for restricted crankcase breather. I added a breather to my cam cover and run the vent hose to my chaingard or a catch can if dictated by race track.
Check for restricted crankcase breather. I added a breather to my cam cover and run the vent hose to my chaingard or a catch can if dictated by race track.
Original owner 78 1000 LTD
Mr Turbo Race Kit, MTC 1075 Turbo pistons by PitStop Performance , Falicon Ultra Lite Super Crank, APE everything. Les Holt @ PDM's Billet Goodies . Frame by Chuck Kurzawa @ Logghe Chassis . Deep sump 5qt oil pan. RIP Bill Hahn
The following user(s) said Thank You: Fastdave61
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Cam End Plugs
08 May 2012 00:27
Or, install the cam plugs so the flange in on the inside, so it can't blow out.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Cam End Plugs
08 May 2012 02:42 - 08 May 2012 02:46
Yamaha 3-bond, let it cure.
Clean off all the old adhesive and oil/grease.
Clean off all the old adhesive and oil/grease.
1979 KZ-750 Twin
Last edit: 08 May 2012 02:46 by bountyhunter.
Please Log in or Create an account to join the conversation.
- Fastdave61
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Re: Cam End Plugs
11 May 2012 22:42
Thanks Hunter: Used Yamabond, installed cover snug let sit over night, installed new gasket, seems to be fine now, hope it stays that way. Thanks again, FD61
what if the Hoke-Pokie is what its all about
what if the Hoke-Pokie is what its all about
1969 BSA A65F Firebird
2004 BMW R1150RT
1980 Kz1000G1
2008 Triumph Tiger 1050
Bemidji, Mn
2004 BMW R1150RT
1980 Kz1000G1
2008 Triumph Tiger 1050
Bemidji, Mn
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
