++ Changing RINGS.
- iamkalaniprince
-
Topic Author
- Offline
- User
-

Registered
- You Rule!
- Posts: 22
- Thanks: 0
++ Changing RINGS.
11 May 2012 16:31
Any other to-do's while your're in there? I may have to do valve guides as well. Any advice?
Much love, Kalani-
Much love, Kalani-
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: ++ Changing RINGS.
11 May 2012 23:44 - 11 May 2012 23:45
I found out valve guides don't wear unless they are abused or installed wrong. My 750 had 75k miles so I bought new guides and the old ones had zero wear.
Definitely do the valves and valve seals.
Definitely do the valves and valve seals.
1979 KZ-750 Twin
Last edit: 11 May 2012 23:45 by bountyhunter.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: ++ Changing RINGS.
12 May 2012 10:01
thats must depend on the model. the kz900/1000 guides do wear out.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: ++ Changing RINGS.
12 May 2012 10:22
One thing for sure... Replace Chain tensioner guides (KZ 900/1000 = plastic/polymer)!
Definitely replace the rubber dampner pads (over the shafts) as well.
BTW, nice on the paint job...
Definitely replace the rubber dampner pads (over the shafts) as well.
BTW, nice on the paint job...
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- BlackZ1R
-
- Offline
- User
-

Registered
- Kawasaki in my blood
- Posts: 700
- Thanks: 47
Re: ++ Changing RINGS.
12 May 2012 10:56
Lap the valves, new timing chain components and guide seals. Tach seal, end plugs. Use NO sealer on cylinder base gasket. Install DRY!! Center O-ring, oil only. NO sealer(no sillycone).
And don't pressure wash that bike.
And don't pressure wash that bike.
Kawasaki
Someone once told me to marry that motorcycle I was riding ......there's times I wish I hadda listened .
Someone once told me to marry that motorcycle I was riding ......there's times I wish I hadda listened .
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: ++ Changing RINGS.
12 May 2012 11:04
You can't accurately tell anything about the condition of the valve guides until you take head apart.
If it's a 900 and virgin, it would have the old OEM bronze guides. 1000's were cast iron. The 1000s held up good. The 900's didn't hold up near as well.
With the lack of lubrication in our fuel today, I would advise replacing valves rather than reface the old ones. Kibble White Valves are a good choice. The aftermarket OEM replacement type valves are cheaper and sometimes quite heavy. You get what you pay for.
New valve springs are also the best option. Again choices are available. Kibble White or APE the two I use predominately. For small cams [stock - .440 lift] I use APE. For serious cams [.440 and up] Kibbles...
If it's a 900 and virgin, it would have the old OEM bronze guides. 1000's were cast iron. The 1000s held up good. The 900's didn't hold up near as well.
With the lack of lubrication in our fuel today, I would advise replacing valves rather than reface the old ones. Kibble White Valves are a good choice. The aftermarket OEM replacement type valves are cheaper and sometimes quite heavy. You get what you pay for.
New valve springs are also the best option. Again choices are available. Kibble White or APE the two I use predominately. For small cams [stock - .440 lift] I use APE. For serious cams [.440 and up] Kibbles...
Larry C.
Please Log in or Create an account to join the conversation.
- BlackZ1R
-
- Offline
- User
-

Registered
- Kawasaki in my blood
- Posts: 700
- Thanks: 47
Re: ++ Changing RINGS.
12 May 2012 11:16LarryC wrote: You can't accurately tell anything about the condition of the valve guides until you take head apart.
If it's a 900 and virgin, it would have the old OEM bronze guides. 1000's were cast iron. The 1000s held up good. The 900's didn't hold up near as well.
With the lack of lubrication in our fuel today, I would advise replacing valves rather than reface the old ones. Kibble White Valves are a good choice. The aftermarket OEM replacement type valves are cheaper and sometimes quite heavy. You get what you pay for.
New valve springs are also the best option. Again choices are available. Kibble White or APE the two I use predominately. For small cams [stock - .440 lift] I use APE. For serious cams [.440 and up] Kibbles...
Larry, is this what you are talking about?
valvetrain.kpmivalvetrain.com/category/i...-900-br-1973-to-1977
Kawasaki
Someone once told me to marry that motorcycle I was riding ......there's times I wish I hadda listened .
Someone once told me to marry that motorcycle I was riding ......there's times I wish I hadda listened .
Please Log in or Create an account to join the conversation.
- iamkalaniprince
-
Topic Author
- Offline
- User
-

Registered
- You Rule!
- Posts: 22
- Thanks: 0
Re: ++ Changing RINGS.
13 May 2012 00:58
Fantastic. Thank you guys!
I'm guessing I don't need to resurface the head or should I since it's off?
Also, is changing the main wiring harness a massive job?
I'm guessing I don't need to resurface the head or should I since it's off?
Also, is changing the main wiring harness a massive job?
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: ++ Changing RINGS.
13 May 2012 07:38 - 13 May 2012 07:47BlackZ1R wrote:LarryC wrote: You can't accurately tell anything about the condition of the valve guides until you take head apart.
If it's a 900 and virgin, it would have the old OEM bronze guides. 1000's were cast iron. The 1000s held up good. The 900's didn't hold up near as well.
With the lack of lubrication in our fuel today, I would advise replacing valves rather than reface the old ones. Kibble White Valves are a good choice. The aftermarket OEM replacement type valves are cheaper and sometimes quite heavy. You get what you pay for.
New valve springs are also the best option. Again choices are available. Kibble White or APE the two I use predominately. For small cams [stock - .440 lift] I use APE. For serious cams [.440 and up] Kibbles...
Larry, is this what you are talking about?
valvetrain.kpmivalvetrain.com/category/i...-900-br-1973-to-1977
Yes.
A clean up cut on the head certainly won't hurt anything. Why not make sure it's flat while it's apart.
Wiring harness is plug and play.
Larry C.
Last edit: 13 May 2012 07:47 by LarryC.
Please Log in or Create an account to join the conversation.
- iamkalaniprince
-
Topic Author
- Offline
- User
-

Registered
- You Rule!
- Posts: 22
- Thanks: 0
Re: ++ Changing RINGS.
13 May 2012 17:06
The bike kept blowing the main fuse for a good while.. Unable to find the intermittent problem, I'm guessing it has to do with the old wiring. Maybe it's grounding out somewhere?
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
