Help! Valve Adjustment

  • adr3naline
  • adr3naline's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 14
  • Thanks: 0

Help! Valve Adjustment

23 May 2012 23:35 - 23 May 2012 23:39
#524393
Today I tested the compression on my 1979 KZ650. Cold and kickstarted, I had 75, 65, 80, and 75.

So, I decided to check the valve clearances to see if I could improve the compression. The clearances I got were (based on feeler gauge sizes): Exhaust - .178, .152, .152, .203, Intake - .102, .063, .076, .102.

Then I checked the shim sizes, based on the numbers written on the shims: Exhaust - 2.60, 2.50, 2.55, 2.50, Intake - 2.55, 2.65, 2.65, 2.50.

I decided to swap shims around so that my clearances were closer to .10 to .15, and I swapped them to this: Exhaust - 2.65, 2.50, 2.55, 2.55, and Intake - 2.50, 2.60, 2.65, 2.50. Based on these changes, I should have the following new clearances: Exhaust - .128, .152, .152, .153, and Intake - .152, .113, .076, and .102.

I made sure to keep the chain tight while pulling buckets to check/replace shims.

When I got it all bolted back up, I rotated the engine a few times to make sure everything was seated. I checked the clearances again... and I couldn't even get my smallest shim between some of these buckets, but the best was .102! I must have done something wrong. My timing chain, before I took off the idler, had some slack in it. Now, it's super tight.

I think that's everything I can remember doing... can you help me? What did I do wrong?

Thank you!
adr3naline
1979 KZ650sr
1979 CB650
Last edit: 23 May 2012 23:39 by adr3naline. Reason: forgot one part

Please Log in or Create an account to join the conversation.

  • munkybrain2010
  • munkybrain2010's Avatar
  • Offline
  • User
  • User
    Registered
  • Clueless..
  • Posts: 43
  • Thanks: 0

Re: Help! Valve Adjustment

24 May 2012 02:04
#524432
Are the buckets in their original valve? I dont know if they would change that much even with the same shims left in if you had switched the buckets. Apparently it makes adjusting after that more difficult.

did you tighten you cam chain tensioner with a longer bolt if its the auto like my 79 before you took off the idler?
Keep it together man!

79 KZ650 "Geto Cycle"

Please Log in or Create an account to join the conversation.

  • adr3naline
  • adr3naline's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 14
  • Thanks: 0

Re: Help! Valve Adjustment

24 May 2012 10:26
#524495
Thanks for getting back with me.

No, the buckets are the exact same at each valve. And I didnt make any adjustments to my chain tensioner.
adr3naline
1979 KZ650sr
1979 CB650

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Help! Valve Adjustment

24 May 2012 10:34
#524501
If the chain is "Super Tight" it is most likely not on the crankshaft sprocket correctly.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • adr3naline
  • adr3naline's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 14
  • Thanks: 0

Re: Help! Valve Adjustment

24 May 2012 11:15
#524513
Motor Head wrote: If the chain is "Super Tight" it is most likely not on the crankshaft sprocket correctly.

So, I can rotate the engine fine though... Is there a way to verify that's it's not on the crank sprocket correctly?
adr3naline
1979 KZ650sr
1979 CB650

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Help! Valve Adjustment

24 May 2012 11:42
#524519
May locate some info through one of these links about re-setting the tensioner.

www.kz650.info/

jarlef.no/Kawasaki/Series/Z/650/z650files.htm

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • munkybrain2010
  • munkybrain2010's Avatar
  • Offline
  • User
  • User
    Registered
  • Clueless..
  • Posts: 43
  • Thanks: 0

Re: Help! Valve Adjustment

24 May 2012 16:52
#524555
The manual says to stop the tensioner with a longer bolt before removal of the cam shafts. if you took slack off the chain the tensioner may have pushed out too far. You should make sure the chain is on tight (no slack between sprocket and crank)on the exhaust side and then timed right with the intake. if the chain is still too tight you may have to tighten the tensioner down with a longer bolt and take it off to see if that is the problem.

Im also curious about the differences in spec too though. I did the same exact thing, rearranging shims and buying two new ones to put it in theoretical spec, but upon inspection only one was at .152! it runs like a rocket though and the spark plugs look MUCH better still.
Keep it together man!

79 KZ650 "Geto Cycle"

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum