TK 22 Dyno jet instructions Suck !
- Gar1800
-
Topic Author
- Offline
- User
-

Registered
- Posts: 47
- Thanks: 2
TK 22 Dyno jet instructions Suck !
02 Jun 2012 23:37
Im trying to put the new needles in and im already stuck on step 4 in section B. I have removed the nut and a screw from the slide arm, after that it says to lift and remove the linkage up and back to remove the slides. When I pull the linkage arm up there isnt any room to remove the linkage arm out of the way to pull out the slide. What am I missing in these directions? So far in section A&B it says to refer to chart 1 ... what chart 1? I have no charts with the directions or the pdf file on the tk 22 carb site
Thanks , Gar
Attachment IMG_14251_2012-06-02.JPG not found
Thanks , Gar
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 00:10 - 03 Jun 2012 00:11
May find some help here:
home.comcast.net/~loudgpz/GPZweb/TK22mainPage/TK22mainPage.html
Good Fortune!
home.comcast.net/~loudgpz/GPZweb/TK22mainPage/TK22mainPage.html
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 03 Jun 2012 00:11 by Patton.
Please Log in or Create an account to join the conversation.
- Gar1800
-
Topic Author
- Offline
- User
-

Registered
- Posts: 47
- Thanks: 2
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 00:18
As much information that's on that site, I couldn't find any help with the details I need. Thank you for your response. Hopfully someone out their has run into this same issue.
Gar
Gar
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 00:48
Am uncertain whether this info from KZr's FILEBASE might be close enough to help. 
www.kzrider.com/filebase/doc_download/208-kzcarbneedleremove
Good Fortune!
www.kzrider.com/filebase/doc_download/208-kzcarbneedleremove
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- The Gringo
-
- Offline
- User
-

Registered
- ¡Usted no necesita otra motocicleta!
- Posts: 1766
- Thanks: 11
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 07:23 - 03 Jun 2012 07:54
There are 2 small phillips screws that attach the linkage to the slide once you take those out the slide will come right out. Look straight down the slide from the top you will see them they are small IIRC they are #1 size phillips.
Andy
Akron, Ohio
80 Z-1 Classic-Sold
84 GPZ1100
79 KZ 1000 LTD
78 KZ 1000 A2
77 KZ 1000 LTD-Sold
76 KZ 900 The definition of a barn find
76 KZ 900-Sold gone to Denmark
KZ 750 times 3, KZ 650 times 8 Sold 1 down to 7
KZ 550 times 2 80 440LTD-Sold
81 CSR 305-Sold 81 Yamaha XS650 Special
Akron, Ohio
80 Z-1 Classic-Sold
84 GPZ1100
79 KZ 1000 LTD
78 KZ 1000 A2
77 KZ 1000 LTD-Sold
76 KZ 900 The definition of a barn find
76 KZ 900-Sold gone to Denmark
KZ 750 times 3, KZ 650 times 8 Sold 1 down to 7
KZ 550 times 2 80 440LTD-Sold
81 CSR 305-Sold 81 Yamaha XS650 Special
Last edit: 03 Jun 2012 07:54 by The Gringo.
Please Log in or Create an account to join the conversation.
- The Gringo
-
- Offline
- User
-

Registered
- ¡Usted no necesita otra motocicleta!
- Posts: 1766
- Thanks: 11
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 07:47 - 03 Jun 2012 07:51Gar I'm attaching a diagram of the carb so you can see what I'm talking about it is #12 in the diagram #13 is the lockwasher you will be removing as well. If you have a screwdriver with a magnetic tip that is helpful especially when it comes time to reassemble.
Andy
Akron, Ohio
80 Z-1 Classic-Sold
84 GPZ1100
79 KZ 1000 LTD
78 KZ 1000 A2
77 KZ 1000 LTD-Sold
76 KZ 900 The definition of a barn find
76 KZ 900-Sold gone to Denmark
KZ 750 times 3, KZ 650 times 8 Sold 1 down to 7
KZ 550 times 2 80 440LTD-Sold
81 CSR 305-Sold 81 Yamaha XS650 Special
Akron, Ohio
80 Z-1 Classic-Sold
84 GPZ1100
79 KZ 1000 LTD
78 KZ 1000 A2
77 KZ 1000 LTD-Sold
76 KZ 900 The definition of a barn find
76 KZ 900-Sold gone to Denmark
KZ 750 times 3, KZ 650 times 8 Sold 1 down to 7
KZ 550 times 2 80 440LTD-Sold
81 CSR 305-Sold 81 Yamaha XS650 Special
Last edit: 03 Jun 2012 07:51 by The Gringo.
Please Log in or Create an account to join the conversation.
- Gar1800
-
Topic Author
- Offline
- User
-

Registered
- Posts: 47
- Thanks: 2
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 12:01
Thanks "The Gringo" thats what I was missing, haha I wonder how long it would have taken me to find those without your help. Thanks so much.
Gar
Gar
Please Log in or Create an account to join the conversation.
- loudhvx
-
- Offline
- KZr Legend
-

Registered
- Posts: 10863
- Thanks: 1622
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 12:45 - 03 Jun 2012 12:57
Yes, I have plans to do a page on replacing the needles on the tk-22 site. There is sort of a trick to it.
Do not remove the nut and screw from the slide arm adjuster mechanism. That is sometimes difficult to get back together, and easy to lose parts. It does not have to come apart. You just need some skinny screwdrivers, blade type for removal, and small philips (JIS, actually) to re-install.
There are two small scres inside the slide that come out in a tricky manner.
Step one is remove the screw holding the arm to the throttle shaft.
The tricky part is removing the tiny screws inside the slide. One can be accessed while the slide is down, but the other can only be accessed while the slide is pulled upward.
After doing it several times it's easy and becomes second nature. It helps to have the exact right set of screwdrivers too.
I edited the diagram to show where there are two screws in case anyone else comes across this thread.
Do not remove the nut and screw from the slide arm adjuster mechanism. That is sometimes difficult to get back together, and easy to lose parts. It does not have to come apart. You just need some skinny screwdrivers, blade type for removal, and small philips (JIS, actually) to re-install.
There are two small scres inside the slide that come out in a tricky manner.
Step one is remove the screw holding the arm to the throttle shaft.
The tricky part is removing the tiny screws inside the slide. One can be accessed while the slide is down, but the other can only be accessed while the slide is pulled upward.
After doing it several times it's easy and becomes second nature. It helps to have the exact right set of screwdrivers too.
I edited the diagram to show where there are two screws in case anyone else comes across this thread.
1981 KZ550 D1 gpz.
Kz550 valve train warning.
Other links.
Kz550 valve train warning.
Other links.
Last edit: 03 Jun 2012 12:57 by loudhvx.
Please Log in or Create an account to join the conversation.
- Gar1800
-
Topic Author
- Offline
- User
-

Registered
- Posts: 47
- Thanks: 2
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 13:38 - 03 Jun 2012 13:46
Ok got to practicing on my spare carbs and its fairly easy now. Great tips.
The next question which I still dont understand is the Dyno kit comes with # 98 mains and bigger. Its suggested by (loudhvx) that I use # 96 mains .. Am I suppose to drill out the stock mains to 96 like the pilots, or am I missing something here?
Gar
The next question which I still dont understand is the Dyno kit comes with # 98 mains and bigger. Its suggested by (loudhvx) that I use # 96 mains .. Am I suppose to drill out the stock mains to 96 like the pilots, or am I missing something here?
Gar
Last edit: 03 Jun 2012 13:46 by Gar1800.
Please Log in or Create an account to join the conversation.
- Gar1800
-
Topic Author
- Offline
- User
-

Registered
- Posts: 47
- Thanks: 2
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 13:58
I have went back and read the instructions again for drilling out the jets and now understand its for drilling the mains and pilots. The TK 22 site is very well done with lots of details and pictures. I my reading comprehension has always been pretty bad. Looks like its a trip to the hardware store for some new drill bits.
Gar
Gar
Please Log in or Create an account to join the conversation.
- The Gringo
-
- Offline
- User
-

Registered
- ¡Usted no necesita otra motocicleta!
- Posts: 1766
- Thanks: 11
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 14:22Gar1800 wrote: Thanks "The Gringo" thats what I was missing, haha I wonder how long it would have taken me to find those without your help. Thanks so much.
Gar
Glad to be of service.
Andy
Akron, Ohio
80 Z-1 Classic-Sold
84 GPZ1100
79 KZ 1000 LTD
78 KZ 1000 A2
77 KZ 1000 LTD-Sold
76 KZ 900 The definition of a barn find
76 KZ 900-Sold gone to Denmark
KZ 750 times 3, KZ 650 times 8 Sold 1 down to 7
KZ 550 times 2 80 440LTD-Sold
81 CSR 305-Sold 81 Yamaha XS650 Special
Akron, Ohio
80 Z-1 Classic-Sold
84 GPZ1100
79 KZ 1000 LTD
78 KZ 1000 A2
77 KZ 1000 LTD-Sold
76 KZ 900 The definition of a barn find
76 KZ 900-Sold gone to Denmark
KZ 750 times 3, KZ 650 times 8 Sold 1 down to 7
KZ 550 times 2 80 440LTD-Sold
81 CSR 305-Sold 81 Yamaha XS650 Special
Please Log in or Create an account to join the conversation.
- loudhvx
-
- Offline
- KZr Legend
-

Registered
- Posts: 10863
- Thanks: 1622
Re: TK 22 Dyno jet instructions Suck !
03 Jun 2012 14:27
Hi Gar,
I get a lot of requests for jet info on KZ550's, and since I have a bad memory, I can't keep everyone's setup straight in my head, so I apologize in advance if you've already told me, but what exhaust do you have and are you running the airbox?
I realize swapping jets around is no easy task when the bike still has the airbox so I understand the desire to get it right the first time. But have we talked about you using the Dynojet kit and/or the 98 mains that come with it?
I get a lot of requests for jet info on KZ550's, and since I have a bad memory, I can't keep everyone's setup straight in my head, so I apologize in advance if you've already told me, but what exhaust do you have and are you running the airbox?
I realize swapping jets around is no easy task when the bike still has the airbox so I understand the desire to get it right the first time. But have we talked about you using the Dynojet kit and/or the 98 mains that come with it?
1981 KZ550 D1 gpz.
Kz550 valve train warning.
Other links.
Kz550 valve train warning.
Other links.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
