plugging tachometer hole
- gonbop
-
Topic Author
- Offline
- User
-

Registered
- Posts: 6
- Thanks: 0
plugging tachometer hole
21 Jun 2012 00:49 - 21 Jun 2012 00:50
Hi all, I am wanting to pull my tach and cap the hole though I am leaving the little stem in, any thoughts?
Thanks
Thanks
1979 kz650c3
Last edit: 21 Jun 2012 00:50 by gonbop.
Please Log in or Create an account to join the conversation.
- 750steve
-
- Offline
- User
-

Registered
- Posts: 584
- Thanks: 3
Re: plugging tachometer hole
21 Jun 2012 14:29
07 ZX6R Race Bike
1977 Z750 B2 Twin
1976 Z650 B1
1977 Z750 B2 Twin
1976 Z650 B1
Please Log in or Create an account to join the conversation.
- damarble
-
- Offline
- User
-

Registered
- Posts: 264
- Thanks: 13
Re: plugging tachometer hole
21 Jun 2012 18:38
That is pretty much my plan as well. On a side note, electrical tape wrapped around the stub of the broken cable does not hold up worth a damn.
Go green, buy a Kawasaki!
82 KZ750M CSR Build Thread
89 ZX600C Streetfighter
82 KZ750M CSR Build Thread
89 ZX600C Streetfighter
Please Log in or Create an account to join the conversation.
- gonbop
-
Topic Author
- Offline
- User
-

Registered
- Posts: 6
- Thanks: 0
Re: plugging tachometer hole
22 Jun 2012 02:47
Great idea, very much appreciate it!
1979 kz650c3
Please Log in or Create an account to join the conversation.
- damarble
-
- Offline
- User
-

Registered
- Posts: 264
- Thanks: 13
Re: plugging tachometer hole
28 Jun 2012 12:20
I couldn't find a M18 bolt so I welded a plug into the end of the threaded part of the tach cable. Clean solution and best of all free.
Go green, buy a Kawasaki!
82 KZ750M CSR Build Thread
89 ZX600C Streetfighter
82 KZ750M CSR Build Thread
89 ZX600C Streetfighter
Please Log in or Create an account to join the conversation.
- Ederer
-
- Offline
- User
-

Registered
- Posts: 68
- Thanks: 5
Re: plugging tachometer hole
04 Oct 2012 10:56
Seems like an ordinary 02 sensor plug would work (m18x1.5)? It would need to be drilled for the stub, but I think it might work. I'm needing to plug mine so I'll report back if it works.
This is what I'm thinking:
www.summitracing.com/parts/fst-30169
This is what I'm thinking:
www.summitracing.com/parts/fst-30169
1980 KZ650 Build
kzrider.com/forum/11-projects/552156-kz6...ect-first-time-build
kzrider.com/forum/11-projects/552156-kz6...ect-first-time-build
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: plugging tachometer hole
04 Oct 2012 12:59 - 04 Oct 2012 13:00
i took the threaded end off of the cable, glued a resized penny into it, then just used it as a cap .
works fine. no stem used.
or u can just buy a block off from verious supliers.
works fine. no stem used.
or u can just buy a block off from verious supliers.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Last edit: 04 Oct 2012 13:00 by mark1122.
Please Log in or Create an account to join the conversation.
- DesertKZ
-
- Offline
- User
-

Registered
- Posts: 227
- Thanks: 20
Re: plugging tachometer hole
05 Oct 2012 00:06
Just curious why people are blocking theirs off, are you all running digital tachs or something? Mine's leaking a little and I was just curious before I replace the oring/seal.
1979 KZ1000 Shaft
1979 CX500C
1975 GT750 Smoker
1979 CX500C
1975 GT750 Smoker
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
