no compression on revalved head?
- richrand
-
Topic Author
- Offline
- User
-

Registered
- Posts: 109
- Thanks: 4
no compression on revalved head?
21 Jun 2012 19:46
I put all new valves in my 1977's head, reassembled the motor but I'm getting no compression. The gasket is new. The valves I used were for a 1976 (square keepers) but it was my understanding that the valves themselves were compatible so long as you used the right keepers (which I did -- i ordered the square ones). Once I determined that there was no compression, I called it a day. Any ideas about what my next step should be? I'm a novice. Thanks.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: no compression on revalved head?
21 Jun 2012 21:15
You say you put some valves in. Please expend on that a bit, did you use new valves, or grind the old ones you had? Did you check the guides, and cut the valve seat angles? Did you check for install height? Check the valve clearance to camshaft? Etc.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- richrand
-
Topic Author
- Offline
- User
-

Registered
- Posts: 109
- Thanks: 4
Re: no compression on revalved head?
21 Jun 2012 22:14Motor Head wrote: You say you put some valves in. Please expend on that a bit, did you use new valves, or grind the old ones you had? Did you check the guides, and cut the valve seat angles? Did you check for install height? Check the valve clearance to camshaft? Etc.
All new valves (but spec for a 1976 not a 1977). I did not check the guides or cut the valve seat angle. I also did not check for install height as I believed these would be OEM spec. I did not check for clearance. Just put them in and put it back together. Being honest here. I need advice. Thanks.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: no compression on revalved head?
21 Jun 2012 22:19
You will be pulling the head back off I would for sure. These things need to be done correctly for it to work, let alone last.
Do you have a manual for your bike, as it is necessary for the specs and procedures. Best to leave such work to a qualified machine shop.
you can take off the valve cover and check the valve clearances, you will find that they are tight, probably. Adjusting them may gain some compression.
Do you have a manual for your bike, as it is necessary for the specs and procedures. Best to leave such work to a qualified machine shop.
you can take off the valve cover and check the valve clearances, you will find that they are tight, probably. Adjusting them may gain some compression.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- richrand
-
Topic Author
- Offline
- User
-

Registered
- Posts: 109
- Thanks: 4
Re: no compression on revalved head?
21 Jun 2012 22:26Motor Head wrote: You will be pulling the head back off I would for sure. These things need to be done correctly for it to work, let alone last.
Do you have a manual for your bike, as it is necessary for the specs and procedures. Best to leave such work to a qualified machine shop.
you can take off the valve cover and check the valve clearances, you will find that they are tight, probably. Adjusting them may gain some compression.
Ok. i'll pull the cover off tomorrow and check the clearances. I do have a manuel. Thanks.
Please Log in or Create an account to join the conversation.
- lemo32
-
- Offline
- User
-

Registered
- The Price of Cool aint cheap
- Posts: 316
- Thanks: 2
Re: no compression on revalved head?
22 Jun 2012 00:12
I would check the clearances first, before pulling head, if that checks out, take head off and set it on its side, pour gas or diesel down in each port, check to see if the valves are leaking, do the same for exaust. If they are leaking most likely you will either need to lap them back in or have a machine shop do a valve job.
1979 kz 1000 06 katana 750
Please Log in or Create an account to join the conversation.
- Tomolu5
-
- Offline
- User
-

Registered
- Posts: 421
- Thanks: 45
Re: no compression on revalved head?
22 Jun 2012 00:58
Hey rich, did you lap the valves? Also with mentioning, money spent with Larry c. Is money well spent, he's right down in morgantown
Mine:
04 Honda rebel 250(wifes)
04 GSXR 750(bolt on galore)
98 CBR 600F3(filter, pipe, adjustable cam sprokets, dyno tune)
76 KZ900A (LTD gauge pods, crash bars, LTD(style)pipes, dyna coils and ignition,headwork and mild port cleanup by cavanaugh racing, K&N filter pods, heck I dunno.
04 Honda rebel 250(wifes)
04 GSXR 750(bolt on galore)
98 CBR 600F3(filter, pipe, adjustable cam sprokets, dyno tune)
76 KZ900A (LTD gauge pods, crash bars, LTD(style)pipes, dyna coils and ignition,headwork and mild port cleanup by cavanaugh racing, K&N filter pods, heck I dunno.
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: no compression on revalved head?
22 Jun 2012 01:15
The valve seats and differant valves need to be machined together to get a good seal
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: no compression on revalved head?
22 Jun 2012 01:18
Hoping the cams and cam chain were correctly installed.
Good Fortune!
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- APE Jay
-
- User
-

Public
- Thanks: 0
Re: no compression on revalved head?
22 Jun 2012 02:17
Before you put it back on the next time, vacuum test it. Most top head shops have a vacuum tester.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: no compression on revalved head?
22 Jun 2012 02:38I'd start there.richrand wrote:Motor Head wrote: You say you put some valves in. Please expend on that a bit, did you use new valves, or grind the old ones you had? Did you check the guides, and cut the valve seat angles? Did you check for install height? Check the valve clearance to camshaft? Etc.
All new valves (but spec for a 1976 not a 1977). I did not check the guides or cut the valve seat angle. I also did not check for install height as I believed these would be OEM spec. I did not check for clearance. Just put them in and put it back together. Being honest here. I need advice. Thanks.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: no compression on revalved head?
22 Jun 2012 02:57 - 22 Jun 2012 02:58Or the mickey mouse version I used: flip the head over and fill the valve pockets with very thin oil and see if it leaks past the valves. You can take motor oil and thin it with mineral spirits.APE Jay wrote: Before you put it back on the next time, vacuum test it. Most top head shops have a vacuum tester.
1979 KZ-750 Twin
Last edit: 22 Jun 2012 02:58 by bountyhunter.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
