Cylinder Block Removal

  • retcol
  • retcol's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 17
  • Thanks: 0

Cylinder Block Removal

28 Jun 2012 21:24
#532460
I've got the cylinder head off OK no problem, but now I can't get the cylinder block off. The pistons move freely up and down so I know the engine isn't seized. I've pounded the crap out of the cylinder block with a rubber mallet like the FSM says to do, but the old girl won't budge. Does anybody know any tricks to break the cylinder block free so I can get it off?
2005 HD Softail Deuce
2003 Kawasaki ZRX1200R
1981 Honda CB900F Super Sport
1978 Kawasaki KZ1000A2 Project Bike

Please Log in or Create an account to join the conversation.

  • 4TheKZ1000
  • 4TheKZ1000's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Cylinder Block Removal

28 Jun 2012 22:28
#532477
Its tough to say without knowing whats gasket material on there. the black fiber gasket was the worst thing I had to deal with. did you try the pry spots and try to work it loose that way? I have used a stiff but thin/wide gasket scraper and hammered it in before with success. just dont loose your patiance and do something stupid.....I know it can suck.

Please Log in or Create an account to join the conversation.

  • retcol
  • retcol's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 17
  • Thanks: 0

Re: Cylinder Block Removal

28 Jun 2012 22:36
#532480
Thanks for the advice, especially the patience part. Can you tell me exactly where the pry places are for the cylinder block?
2005 HD Softail Deuce
2003 Kawasaki ZRX1200R
1981 Honda CB900F Super Sport
1978 Kawasaki KZ1000A2 Project Bike

Please Log in or Create an account to join the conversation.

  • 4TheKZ1000
  • 4TheKZ1000's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Cylinder Block Removal

28 Jun 2012 22:45 - 28 Jun 2012 22:53
#532488
front of lower cases were the cylinder meets the cases there will be a grove thats it. Where is your manual....if you dont have one get one or find a free download.
Last edit: 28 Jun 2012 22:53 by 4TheKZ1000.

Please Log in or Create an account to join the conversation.

  • BohicaBob
  • BohicaBob's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 266
  • Thanks: 35

Re: Cylinder Block Removal

28 Jun 2012 23:25
#532496
I use a thick flat steel bar that I drilled two holes in to match up to the two 6 mm threaded holes in the top of the cylinder block. High grade bolts through the bar and into the cylinder block secure the bar.

Even force alternately applied to each side of the bar with a heavy duty plastic, not metal, hammer always does the trick without any damage whatsoever to any fins or crankcase surfaces.
The following user(s) said Thank You: wireman

Please Log in or Create an account to join the conversation.

  • retcol
  • retcol's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 17
  • Thanks: 0

Re: Cylinder Block Removal

28 Jun 2012 23:55
#532509
I tried the prying with a large flat screwdriver, but that didn't do anything except enlarge the pry slot. I'll try the bar with holes suggestion.
2005 HD Softail Deuce
2003 Kawasaki ZRX1200R
1981 Honda CB900F Super Sport
1978 Kawasaki KZ1000A2 Project Bike

Please Log in or Create an account to join the conversation.

  • 4TheKZ1000
  • 4TheKZ1000's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Cylinder Block Removal

28 Jun 2012 23:58 - 29 Jun 2012 00:01
#532512
.


DAMM
Last edit: 29 Jun 2012 00:01 by 4TheKZ1000.

Please Log in or Create an account to join the conversation.

  • BohicaBob
  • BohicaBob's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 266
  • Thanks: 35

Re: Cylinder Block Removal

29 Jun 2012 10:20 - 29 Jun 2012 22:10
#532587
As I said, use a very thick (and heavy) flat bar. The first time I tried a thin bar (only because I had one in my garage) but I bent both ends hitting of it with the heavy plastic mallet.

When I used a 3/4" thick steel flat bar, removing the cylinder block was easy. Again, use heavy duty 6 mm bolts and ensure both bolts are tightened to have snug fit to better transfer the upward force from the flat bar to the cylinder block.
Last edit: 29 Jun 2012 22:10 by BohicaBob.

Please Log in or Create an account to join the conversation.

  • peter1958
  • peter1958's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1553
  • Thanks: 198

Re: Cylinder Block Removal

29 Jun 2012 18:15
#532675
I hit mine with a rubber mallet for hours and all I got was pissed off. Put engine in a rack and turned it upside down hit twice and it came off. I know this doesnt help if its in the bike.

Please Log in or Create an account to join the conversation.

  • BB
  • BB's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 51
  • Thanks: 0

Re: Cylinder Block Removal

30 Jun 2012 19:31
#532846
I just did this, keep banging and banging. Also, I know this will make a lot of guys wince, but I very gently tapped and small flat head screwdriver in the gap. Very gently and about 4 million taps will do the trick.

If and when you split the cases, there is a bolt under the started that will be invisible. Make sure you take this out, I missed it and when I split the cases I snapped this one.

I spent literally 10 hours working on the gaskets, what worked for me was a gasket scraper for the big stuff and then a good week soak with WD40, re wetting it as often as possible. Then use carb cleaner and a scotchbrite.
1980 KZ1000P - The Mistress
2002 R1150GS - Matilda

Please Log in or Create an account to join the conversation.

  • 4TheKZ1000
  • 4TheKZ1000's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Cylinder Block Removal

30 Jun 2012 19:40
#532848
ya, that black fiber gaskets are the worst to remove. :evil:

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum