are these washers supposed to be here?
- KZ1000inaus
-
Topic Author
- Offline
- User
-

Registered
- Luminous Red KZ1000 A2
- Posts: 135
- Thanks: 4
are these washers supposed to be here?
06 Jul 2012 03:47
one removing the upper cam chain cog i dropped one of the oblong washers into the engine which i will hopefully retrieve this weekend.
But on looking at the Kawasaki diagrams it seems they shouldn't be there (unless i just can't see them). The pic shows the one that's left. They sit on the bottom and look a little home made.
Are they supposed to be there? if not are they a known modification?
But on looking at the Kawasaki diagrams it seems they shouldn't be there (unless i just can't see them). The pic shows the one that's left. They sit on the bottom and look a little home made.
Are they supposed to be there? if not are they a known modification?
Attachment UpperCam.jpg not found
Please Log in or Create an account to join the conversation.
- Garn
-
- Offline
- User
-

Registered
- Posts: 265
- Thanks: 13
Re: are these washers supposed to be here?
06 Jul 2012 07:24 - 06 Jul 2012 20:53
KzInAus, The plate on the bottom left should be in that assembly. The whole sprocket assembly is designed to be shock (rubber) mounted.
So, the both sides are made up of two rubber mounting block (a bottom and top) both are different, a bottom plate and a top plate, both different as the bottom has smaller holes, and two dowel pieces with a larger head to the top.
I'll have a look tomorrow to verify my memory. [See slight correction below]
RegardZ.
So, the both sides are made up of two rubber mounting block (a bottom and top) both are different, a bottom plate and a top plate, both different as the bottom has smaller holes, and two dowel pieces with a larger head to the top.
I'll have a look tomorrow to verify my memory. [See slight correction below]
RegardZ.
1 x 73 Z1 (Jaffa), 74 Z1A, 76 Z900-A4
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
Last edit: 06 Jul 2012 20:53 by Garn.
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: are these washers supposed to be here?
06 Jul 2012 08:13
yea, you'll have to fish that out, get a light and see if u can spot it, mine was visible and we fished it out with a piece of welding wire, u could also use a magnet, it could have gone all the way down and be in the oil pan but i wouldnt bet on it, check those rubbers, if they've gotten hard replace em , they get brittle with age
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: are these washers supposed to be here?
06 Jul 2012 10:16
Pulling the Sump would be a good Idea anyway, as you already have the Top off, and you can clean all the Gunk out. Make sure there is nothing stuck in the oil pick up screen, see if there is any metallic debris, etc.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: are these washers supposed to be here?
06 Jul 2012 16:40yes check that screen, an excellent ideaMotor Head wrote: Pulling the Sump would be a good Idea anyway, as you already have the Top off, and you can clean all the Gunk out. Make sure there is nothing stuck in the oil pick up screen, see if there is any metallic debris, etc.
Please Log in or Create an account to join the conversation.
- RonKZ650
-
- Offline
- User
-

Registered
- Posts: 3719
- Thanks: 252
Re: are these washers supposed to be here?
06 Jul 2012 19:16
The rectangular rubber dampers have steel plate built in to them, basically 2 pieces of steel with rubber sandwiched between them. There is no external oblong washer used, so I believe that a hack of some kind. Probably a misguided attempt to increase pressure on the hardened rubber in the sandwich.
321,000 miles on KZ's that I can remember. Not going to see any more.
Please Log in or Create an account to join the conversation.
- Garn
-
- Offline
- User
-

Registered
- Posts: 265
- Thanks: 13
Re: are these washers supposed to be here?
06 Jul 2012 21:17
I have a slight correction to my original post. Looking at the Model Z1000-A2, I realize I am incorrect about the lower plate having smaller holes.
On your model the two plates have 6mm clearance holes on each side and both top and bottom are the same.
As Ron says, the rubber dampers have steel plates built in to them, however, this vulcanised joint does separate leaving the plate and rubber block as individual items. Do check to see if there is not a plate on the rubber already.
RegardZ.
On your model the two plates have 6mm clearance holes on each side and both top and bottom are the same.
As Ron says, the rubber dampers have steel plates built in to them, however, this vulcanised joint does separate leaving the plate and rubber block as individual items. Do check to see if there is not a plate on the rubber already.
RegardZ.
1 x 73 Z1 (Jaffa), 74 Z1A, 76 Z900-A4
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
Please Log in or Create an account to join the conversation.
- KZ1000inaus
-
Topic Author
- Offline
- User
-

Registered
- Luminous Red KZ1000 A2
- Posts: 135
- Thanks: 4
Re: are these washers supposed to be here?
06 Jul 2012 23:47
thanks all
i'll get the sump off tomorrow and see if i can find it as i can't see it from the top to retrieve it
i'll get the sump off tomorrow and see if i can find it as i can't see it from the top to retrieve it
Please Log in or Create an account to join the conversation.
- KZ1000inaus
-
Topic Author
- Offline
- User
-

Registered
- Luminous Red KZ1000 A2
- Posts: 135
- Thanks: 4
Re: are these washers supposed to be here?
06 Jul 2012 23:48by the way i ordered new rubbers from Z1enterprises and they don't have the metal on them it's just rubber.Garn wrote: I have a slight correction to my original post. Looking at the Model Z1000-A2, I realize I am incorrect about the lower plate having smaller holes.
On your model the two plates have 6mm clearance holes on each side and both top and bottom are the same.
As Ron says, the rubber dampers have steel plates built in to them, however, this vulcanised joint does separate leaving the plate and rubber block as individual items. Do check to see if there is not a plate on the rubber already.
RegardZ.
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: are these washers supposed to be here?
06 Jul 2012 23:56 - 06 Jul 2012 23:58
I got mine separate, dont think they are made as a unit
Last edit: 06 Jul 2012 23:58 by jonnybravo.
Please Log in or Create an account to join the conversation.
- KZ1000inaus
-
Topic Author
- Offline
- User
-

Registered
- Luminous Red KZ1000 A2
- Posts: 135
- Thanks: 4
Re: are these washers supposed to be here?
07 Jul 2012 02:09
pulled off the sump (i think it was it's first time off since new !!)
and it was in there.. wooo hooo!!
plain sailing from here on in then..
rebuild next week.. or when the parts turn up anyway..
and it was in there.. wooo hooo!!
plain sailing from here on in then..
rebuild next week.. or when the parts turn up anyway..
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
