2 questions

  • pete greek1
  • pete greek1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1510
  • Thanks: 185

2 questions

14 Jul 2012 14:06
#535860
can I reuse the copper washers for the head bolts ? and would 29 smoothbores work on a stock 76 LTD 900, with a kerker, stock airbox ?
1980 LTD 1000..,1976 LTD 900, have the 1000&900 now. the rest are previous= 1978 KZ 650 B.., 1980 Yamaha XT 500..,1978 Yamaha DT 400.., 1977 Yamaha yz 80..,Honda trail ct 70.., Honda QA 50...5-1/2 hp brigs & straton CAT chopper mini bike...3-1/2 hp mini bike (WHEN GAS WAS ABOUT 45 CENTS A GALLON)!!!!

Please Log in or Create an account to join the conversation.

  • 4TheKZ1000
  • 4TheKZ1000's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: 2 questions

14 Jul 2012 14:13 - 14 Jul 2012 14:14
#535861
on the copper washers....if they are ok without major wear grooves should seal ok, put the best side down. on the 29's....I have seen them on close to stock 1000's but I really dont know about 900's....will need someone else to chime in on that one.
Last edit: 14 Jul 2012 14:14 by 4TheKZ1000.

Please Log in or Create an account to join the conversation.

  • pig9r
  • pig9r's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 64
  • Thanks: 10

Re: 2 questions

14 Jul 2012 17:14
#535895
I would anneal them by heating them up with a propane torch until they are glowing red hot. A propane torch is good because it won't get hot enough to melt them. Then let them air cool - don't quench them. Then lay some sand paper flat and clean them up and remove the old ridges from the nuts.

Please Log in or Create an account to join the conversation.

  • peter1958
  • peter1958's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1553
  • Thanks: 198

Please Log in or Create an account to join the conversation.

  • Tomolu5
  • Tomolu5's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 421
  • Thanks: 45

Re: 2 questions

14 Jul 2012 17:30
#535900
+ 1 on annealing them
Mine:
04 Honda rebel 250(wifes)
04 GSXR 750(bolt on galore)
98 CBR 600F3(filter, pipe, adjustable cam sprokets, dyno tune)
76 KZ900A (LTD gauge pods, crash bars, LTD(style)pipes, dyna coils and ignition,headwork and mild port cleanup by cavanaugh racing, K&N filter pods, heck I dunno.

Please Log in or Create an account to join the conversation.

  • pete greek1
  • pete greek1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1510
  • Thanks: 185

Re: 2 questions

14 Jul 2012 19:23
#535914
Thanks to every one for the answers to my questions....I just was"nt sure...Pete
1980 LTD 1000..,1976 LTD 900, have the 1000&900 now. the rest are previous= 1978 KZ 650 B.., 1980 Yamaha XT 500..,1978 Yamaha DT 400.., 1977 Yamaha yz 80..,Honda trail ct 70.., Honda QA 50...5-1/2 hp brigs & straton CAT chopper mini bike...3-1/2 hp mini bike (WHEN GAS WAS ABOUT 45 CENTS A GALLON)!!!!

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: 2 questions

14 Jul 2012 21:47
#535933
Heat them up and toss them in a bucket of cold water B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: 2 questions

14 Jul 2012 21:57
#535936
When you heat something just like a pipe fitting to loosen it up it will expand,but as it cools it shrinks back down.
When you heat up a piece of copper thats been crushed then toss it in water it will stay expanded. B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • pig9r
  • pig9r's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 64
  • Thanks: 10

Re: 2 questions

14 Jul 2012 22:31
#535944
wireman wrote: When you heat something just like a pipe fitting to loosen it up it will expand,but as it cools it shrinks back down.
When you heat up a piece of copper thats been crushed then toss it in water it will stay expanded. B)

Problem is when you quench it, it doesn't stay soft and is more brittle. If it air cools it will stay soft. Either way they will likely seal just fine.

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: 2 questions

14 Jul 2012 22:41
#535947
Ive been sweating copper for a living on/off for last 30 years,copper is not steel cooling it off with water doesnt hurt it like it does steel.
Although people have been tempering steel in brine/salt water since long before either of us were around. B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • pig9r
  • pig9r's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 64
  • Thanks: 10

Re: 2 questions

15 Jul 2012 00:23 - 15 Jul 2012 00:23
#535984
wireman wrote: Ive been sweating copper for a living on/off for last 30 years,copper is not steel cooling it off with water doesnt hurt it like it does steel.
Although people have been tempering steel in brine/salt water since long before either of us were around. B)

You're right, i wasn't thinking, nonferrous, so same result either way.
Last edit: 15 Jul 2012 00:23 by pig9r.
The following user(s) said Thank You: wireman

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: 2 questions

15 Jul 2012 09:04
#536024
If your copper washers are only copper clad [coated with but not made of copper] then Annealing them is a waste of time.

You have two options. Toss them and get new ones or lightly sand them and spray them with copper coat. You could even use a dab of engine case sealer on them.
Larry C.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum