is this a no go?
- Pop147
-
Topic Author
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 0
is this a no go?
26 Aug 2012 13:42
There is a chip on out put shaft upper case half. It feels smooth to the touch but, its fairly deep. Also there is some wear on the side of the crank case upper half. Is this case half reusable?
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: is this a no go?
26 Aug 2012 14:11
What kind of bike? Id have the crankshaft checked
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Pop147
-
Topic Author
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 0
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: is this a no go?
26 Aug 2012 14:40
Is there a hole in the case for a pin to keep that bearing from spinning?
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- OldSchoolZ
-
- Offline
- User
-

Registered
- Posts: 217
- Thanks: 33
Re: is this a no go?
26 Aug 2012 15:21
It appears the bearing had seized at least slightly and spun. When you install your new bearing tighten everything and make sure you cant move the bearing by lightly tapping the outter casing.
It should remain tight. With a new free spinning bearing, it shouldnt stress the case anymore.
Bottom line is, that bearing needs to be tight when cases are tightened.
It should remain tight. With a new free spinning bearing, it shouldnt stress the case anymore.
Bottom line is, that bearing needs to be tight when cases are tightened.
Remember, don't work on your bike so much you never ride it.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: is this a no go?
26 Aug 2012 16:12dumb question: could you use some kind of adhesive "dots" when you install the insert so it can't spin while it breaks in?OldSchoolZ wrote: It appears the bearing had seized at least slightly and spun. When you install your new bearing tighten everything and make sure you cant move the bearing by lightly tapping the outter casing.
It should remain tight. With a new free spinning bearing, it shouldnt stress the case anymore.
Bottom line is, that bearing needs to be tight when cases are tightened.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: is this a no go?
26 Aug 2012 16:34
Ive seen them loc tited before to hold the,not sure if I agree with it though
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Pop147
-
Topic Author
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 0
Re: is this a no go?
26 Aug 2012 17:35
well while im here im going to take the transmission apart and the manual says to get new circlips can i use any circlips or just oem from Kawasaki?
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: is this a no go?
26 Aug 2012 17:51
Id go oem
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Pop147
-
Topic Author
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 0
Re: is this a no go?
26 Aug 2012 19:14
oldschool are you talking about the waer in picture 5043?
Please Log in or Create an account to join the conversation.
- OldSchoolZ
-
- Offline
- User
-

Registered
- Posts: 217
- Thanks: 33
Re: is this a no go?
26 Aug 2012 19:53 - 26 Aug 2012 19:54
yea, I was looking at the aluminum that has been scored by the outer bearing spinning.
I was pretty sure you were referring to an input or output shaft for the tranny.
Another thing I've seen done to take up space on a spun bearing was to take a center punch(pointed) and centerpunch a small mark where the bearing makes contact with the case. I'de make about 10 punch marks evenly spaced in a circle. This will push a little bit of the aluminum upwards and take up the gap made by the spun bearing. I've done it before and worked fine, some use a small bit of locktite in conjunction with the punch marks, its actually a decent fix for no money. I suspect it would be a very long time before you have to worry about a new bearing trying to spin.
I was pretty sure you were referring to an input or output shaft for the tranny.
Another thing I've seen done to take up space on a spun bearing was to take a center punch(pointed) and centerpunch a small mark where the bearing makes contact with the case. I'de make about 10 punch marks evenly spaced in a circle. This will push a little bit of the aluminum upwards and take up the gap made by the spun bearing. I've done it before and worked fine, some use a small bit of locktite in conjunction with the punch marks, its actually a decent fix for no money. I suspect it would be a very long time before you have to worry about a new bearing trying to spin.
Remember, don't work on your bike so much you never ride it.
Last edit: 26 Aug 2012 19:54 by OldSchoolZ.
Please Log in or Create an account to join the conversation.
- Pop147
-
Topic Author
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 0
Re: is this a no go?
26 Aug 2012 21:41
No that picture is of the crank shaft. Number 1 is where the chunk of metal is missing and number 2 is where the wear is. Sorry that was my fault.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
