Low RPM stumble
- reborn650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 693
- Thanks: 5
Low RPM stumble
28 Aug 2012 00:40
Hey gang. Would appreciate some input here...
Pulled the carbs soaked the bowls and cleaned the main jets. Air screws 1.5 turns. New Dyna coils, plug wires and caps. Takes about 4-5 minutes to warm up with half choke but I get the occasional backfire through one carb.
When I pull away the old girl stumbles in the lower rpm range but once it hits about 3500 rpm it seems to clear itself and the acceleration is impressive. Anyone have some direction on where I should be looking?
Carbs are from WG #17.5 pilot jets, 1.5 slide cut outs, 5DL31-3 jet needles and #122.5 main jets. Float levels are correct as are slides.
Any input would be appreciated.
Cheers-Colin Firth
Pulled the carbs soaked the bowls and cleaned the main jets. Air screws 1.5 turns. New Dyna coils, plug wires and caps. Takes about 4-5 minutes to warm up with half choke but I get the occasional backfire through one carb.
When I pull away the old girl stumbles in the lower rpm range but once it hits about 3500 rpm it seems to clear itself and the acceleration is impressive. Anyone have some direction on where I should be looking?
Carbs are from WG #17.5 pilot jets, 1.5 slide cut outs, 5DL31-3 jet needles and #122.5 main jets. Float levels are correct as are slides.
Any input would be appreciated.
Cheers-Colin Firth
-1977 Kz650 Custom bought new by brother. Now with 810 kit, GPz750 cams, intake valves, Mikuni 29 smoothbores, velocity stacks, Dyna Igntion, MAC pipe and other goodies.
-1982 Ferrari 308 GTSi Red/Tan
-Toyota FJ Cruiser - 6 speed tank
-2010 Mazda CX-7 Turbo (my bride's)
-1998 Jeep TJ Wrangler 4.0 litre for the kids
-1975 Zamboni - The real Italian sportscar fully restored and functioning every winter at our local outdoor playground rink.
Mine is an ecclectic collection of motorized toys - LOL
I have a newspaper route and a web site where you can plan your own funeral life celebration www.mysendoff.com ....and go out with your own style.
-1982 Ferrari 308 GTSi Red/Tan
-Toyota FJ Cruiser - 6 speed tank
-2010 Mazda CX-7 Turbo (my bride's)
-1998 Jeep TJ Wrangler 4.0 litre for the kids
-1975 Zamboni - The real Italian sportscar fully restored and functioning every winter at our local outdoor playground rink.
Mine is an ecclectic collection of motorized toys - LOL
I have a newspaper route and a web site where you can plan your own funeral life celebration www.mysendoff.com ....and go out with your own style.
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Low RPM stumble
28 Aug 2012 00:47
What year and model of bike?
How's the mechanical ignition advancer working? If it's sticking, this might be the problem. Most are behind a CD sized right engine cover at the end of the crankshaft. With the engine off, give it a twist, it should snap back to original position.
If it's stuck, make note of how it's assembled, as it can be re-assembled 180 degrees out. Usually some light grease or 3-in-one oil on the weight pivots and the tube it moves on are about all it needs. I check my bikes advancer every time I do an oil change for smooth operation.
How's the mechanical ignition advancer working? If it's sticking, this might be the problem. Most are behind a CD sized right engine cover at the end of the crankshaft. With the engine off, give it a twist, it should snap back to original position.
If it's stuck, make note of how it's assembled, as it can be re-assembled 180 degrees out. Usually some light grease or 3-in-one oil on the weight pivots and the tube it moves on are about all it needs. I check my bikes advancer every time I do an oil change for smooth operation.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- reborn650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 693
- Thanks: 5
Re: Low RPM stumble
28 Aug 2012 01:00 - 28 Aug 2012 01:40
Pulled the points cover and this is what I have for the Dyna S plate. I will have to pull the plate to get to the mechanical advance behind the plate and lube the mechanical advance? Noticed that the four mounting screws for the magnets were slightly loose.
Attachment DynaSplateKz650.jpg not found
Attachment DSC02826.jpg not found
-1977 Kz650 Custom bought new by brother. Now with 810 kit, GPz750 cams, intake valves, Mikuni 29 smoothbores, velocity stacks, Dyna Igntion, MAC pipe and other goodies.
-1982 Ferrari 308 GTSi Red/Tan
-Toyota FJ Cruiser - 6 speed tank
-2010 Mazda CX-7 Turbo (my bride's)
-1998 Jeep TJ Wrangler 4.0 litre for the kids
-1975 Zamboni - The real Italian sportscar fully restored and functioning every winter at our local outdoor playground rink.
Mine is an ecclectic collection of motorized toys - LOL
I have a newspaper route and a web site where you can plan your own funeral life celebration www.mysendoff.com ....and go out with your own style.
-1982 Ferrari 308 GTSi Red/Tan
-Toyota FJ Cruiser - 6 speed tank
-2010 Mazda CX-7 Turbo (my bride's)
-1998 Jeep TJ Wrangler 4.0 litre for the kids
-1975 Zamboni - The real Italian sportscar fully restored and functioning every winter at our local outdoor playground rink.
Mine is an ecclectic collection of motorized toys - LOL
I have a newspaper route and a web site where you can plan your own funeral life celebration www.mysendoff.com ....and go out with your own style.
Last edit: 28 Aug 2012 01:40 by reborn650.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Low RPM stumble
28 Aug 2012 10:15 - 28 Aug 2012 10:16
After cleaning/ lubing, get out your timing light and check both pick-up coils are set correctly as they are independently adjustable. The 4 screws you said were loose.
make sure you have no vacuum leaks before carb adjustments.
Then a Dynamic Carb Sync, with a Manometer. Get the carbs sync real good, and the ignition set up. then maybe set the Idle mixture up slightly richer on fuel. Each screw will not be exactly the same for optimum running. Turning them out to 1-1/2 turns is just the starting point for a Dynamic sync.
make sure you have no vacuum leaks before carb adjustments.
Then a Dynamic Carb Sync, with a Manometer. Get the carbs sync real good, and the ignition set up. then maybe set the Idle mixture up slightly richer on fuel. Each screw will not be exactly the same for optimum running. Turning them out to 1-1/2 turns is just the starting point for a Dynamic sync.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 28 Aug 2012 10:16 by Motor Head.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
