More issues. '82 1100A
- pickardracing
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 1
More issues. '82 1100A
14 Sep 2012 19:28 - 14 Sep 2012 19:29
Well here's the latest.
Spent a bunch of money on plugs, wires, caps, etc. Went through the entire wiring harness, cleaned every connector alive with de-oxit. Everything has good voltage, spark looked good, compression tests came out fine, I'm lost.
There's no reason (other than carbs) that this piece of $#!t won't run. Started decently, but smoked like a damn chimney on startup out of the LH muffler. Go ahead and watch the video. That's the noise it makes in the engine when running, and it will absolutely not idle or run below 1500rpm.
Any ideas or help would be fantastic. If I can't figure this out, I'll likely just part it out to get my money back and say eff it.
Thanks guys.
Spent a bunch of money on plugs, wires, caps, etc. Went through the entire wiring harness, cleaned every connector alive with de-oxit. Everything has good voltage, spark looked good, compression tests came out fine, I'm lost.
There's no reason (other than carbs) that this piece of $#!t won't run. Started decently, but smoked like a damn chimney on startup out of the LH muffler. Go ahead and watch the video. That's the noise it makes in the engine when running, and it will absolutely not idle or run below 1500rpm.
Any ideas or help would be fantastic. If I can't figure this out, I'll likely just part it out to get my money back and say eff it.
Thanks guys.
Current: 1982 KZ1100 A2
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Last edit: 14 Sep 2012 19:29 by pickardracing.
Please Log in or Create an account to join the conversation.
- P21
-
- Offline
- User
-

Registered
- Posts: 471
- Thanks: 34
Re: More issues. '82 1100A
14 Sep 2012 20:29
its not that hard of a job but i would pull carbs off and have a look you would be surprised whats under them bowls.
sounds like slow jets are bound up.
1500 rpm down is controlled my them
sounds like slow jets are bound up.
1500 rpm down is controlled my them
Kawasaki KZ 1000 Police (2002) P21
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- pickardracing
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 1
Re: More issues. '82 1100A
14 Sep 2012 23:52
The coil/plug wires are hooked up correctly.
Would carbs cause this ridiculous smoking and noise? I mean I understand that they'll cause all sorts of issues, but heavy smoke and sounding like it's going to shit the bed?
Would carbs cause this ridiculous smoking and noise? I mean I understand that they'll cause all sorts of issues, but heavy smoke and sounding like it's going to shit the bed?
Current: 1982 KZ1100 A2
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Please Log in or Create an account to join the conversation.
- pickardracing
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 1
Re: More issues. '82 1100A
15 Sep 2012 18:43 - 15 Sep 2012 18:45
Looks like I'm chasing multiple issues. Pulled off the stator cover to find the starter clutch barely holding on, and causing the knocking noise. Ordering rebuild kit for it and new screws. After that, we'll dig in the carbs.
Current: 1982 KZ1100 A2
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Last edit: 15 Sep 2012 18:45 by pickardracing.
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: More issues. '82 1100A
15 Sep 2012 18:52
Some engines have a woodruff key on the alternator shaft, preventing the rotor from spinning. The key resembles a half moon shape with a machined slot in the crankshaft where the rotor goes.Others are nothing more than being held on the shaft with the torque from the rotor bolt.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- pickardracing
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 1
Re: More issues. '82 1100A
15 Sep 2012 19:50 - 15 Sep 2012 19:51
Looks like the 3 mounting bolts for the starter clutch are FUBAR. Z1 doesn't list them, am I screwed with having to go to the dealer? They have 12.9 stamped on them so I'm assuming a regular grade bolt won't do the trick.
Current: 1982 KZ1100 A2
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Past: 1980 GS750L - 1978 GS1000 - 1978 GS750
1983 GS750 - 2001 ZRX1200R - 2001 YZF-R6
Last edit: 15 Sep 2012 19:51 by pickardracing.
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: More issues. '82 1100A
15 Sep 2012 20:35
Those are probably metric version of a grade 8 bolt.
My speakers dont work on my computer so I couldnt hear your video but once you get the starter clutch back together it definately wouldnt hurt to clean/scrub carbs out if its black smoke rolling out your exhuast when you start it id guess fuel.
As long as youre in there pick up a valve cover gasket and check valve clearances,a cylinder with a valve hanging open would be tough to start also and would need a higher idle to compensate for lower compression to keep it running
My speakers dont work on my computer so I couldnt hear your video but once you get the starter clutch back together it definately wouldnt hurt to clean/scrub carbs out if its black smoke rolling out your exhuast when you start it id guess fuel.
As long as youre in there pick up a valve cover gasket and check valve clearances,a cylinder with a valve hanging open would be tough to start also and would need a higher idle to compensate for lower compression to keep it running
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: More issues. '82 1100A
15 Sep 2012 20:41 - 15 Sep 2012 20:43
Babbits shows those as being 8x16mm socket/allen head bolts,might be a lot cheaper to get them through bolt depot.com
Bolt depot shows those bolts for .23 each on their site.
Bolt depot shows those bolts for .23 each on their site.
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Last edit: 15 Sep 2012 20:43 by wireman.
Please Log in or Create an account to join the conversation.
- Del_Herring
-
- Offline
- User
-

Registered
- Posts: 278
- Thanks: 29
Re: More issues. '82 1100A
15 Sep 2012 20:43
Yes 12.9 is their grade. It's roughly equivalent to a grade 8, but metric.
www.engineeringtoolbox.com/steel-bolts-m...c-grades-d_1428.html
www.engineeringtoolbox.com/steel-bolts-sae-grades-d_1426.html
think it actually works out a little stronger than a grade 8, but same idea. If it's a standard bolt size (sometimes you get lucky), you can pick up 12.9 class bolts at an Ace Hardware, or equivalent.
www.engineeringtoolbox.com/steel-bolts-m...c-grades-d_1428.html
www.engineeringtoolbox.com/steel-bolts-sae-grades-d_1426.html
think it actually works out a little stronger than a grade 8, but same idea. If it's a standard bolt size (sometimes you get lucky), you can pick up 12.9 class bolts at an Ace Hardware, or equivalent.
1983 KZ750-N2 Spectre
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: More issues. '82 1100A
15 Sep 2012 20:58
Try
www.boltdepot.com
Most local hardware stores may not carry bolts with the correct hardness, and they could either strip out or shear off. Don't use SS there as thet are softer than steel grade 5 bolts.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: More issues. '82 1100A
16 Sep 2012 09:53MFolks wrote: Some engines have a woodruff key on the alternator shaft, preventing the rotor from spinning. The key resembles a half moon shape with a machined slot in the crankshaft where the rotor goes.Others are nothing more than being held on the shaft with the torque from the rotor bolt.
Kawasaki quit using that setup in 79. It helps if you've actually worked on bikes that you post tips on how to fix
Larry C.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
