Ring Seating
- lemo32
-
Topic Author
- Offline
- User
-

Registered
- The Price of Cool aint cheap
- Posts: 316
- Thanks: 2
Ring Seating
22 Sep 2012 09:20
I have a 79 kz 1000 ltd, just went through motor, valves adjusted, new rings, fresh hone, all spec out to manual, anyhow, not getting good compression, around 100 on all four, and when i dump, oil into it, I get 120 across all, well compression go up as rings seat? or is this the best i can expect.
1979 kz 1000 06 katana 750
Please Log in or Create an account to join the conversation.
- lemo32
-
Topic Author
- Offline
- User
-

Registered
- The Price of Cool aint cheap
- Posts: 316
- Thanks: 2
Re: Ring Seating
22 Sep 2012 09:26
Havent started motor yet, and that 100 is with carbs off.
1979 kz 1000 06 katana 750
Please Log in or Create an account to join the conversation.
- 4TheKZ1000
-
- User
-

Public
- Thanks: 0
Re: Ring Seating
22 Sep 2012 09:58
Just a few things come to mind......
Did you gap pistion rings to the cyclinder.
Did you stagger piston ring gaps thoughout the cyclinder.
Is the cam timing correct...if not compression will leak out valves.
Did you adjust the valve clearance correctly and recheck.
Did you gap pistion rings to the cyclinder.
Did you stagger piston ring gaps thoughout the cyclinder.
Is the cam timing correct...if not compression will leak out valves.
Did you adjust the valve clearance correctly and recheck.
Please Log in or Create an account to join the conversation.
- lemo32
-
Topic Author
- Offline
- User
-

Registered
- The Price of Cool aint cheap
- Posts: 316
- Thanks: 2
Re: Ring Seating
22 Sep 2012 10:25
yeah, all the above, staggered rings, checked gap, checked piston in bore via feeler guage, all that checked out, also adjusted valves to within .004 on all cyl, did leakdown not leaking at valves, so must be bottom end.
1979 kz 1000 06 katana 750
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: Ring Seating
22 Sep 2012 10:44
Put some miles on the motor and recheck.
How did you clean the bores before putting motor together?
How did you clean the bores before putting motor together?
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Garn
-
- Offline
- User
-

Registered
- Posts: 265
- Thanks: 13
Re: Ring Seating
25 Sep 2012 04:17 - 25 Sep 2012 04:19The rings have to bed into the bore, that's where the cross-hatch pattern on the honing comes into play. Give it about 20 miles or so and I'm sure it will improve.wireman wrote: Put some miles on the motor and recheck.
RegardZ
1 x 73 Z1 (Jaffa), 74 Z1A, 76 Z900-A4
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
Last edit: 25 Sep 2012 04:19 by Garn.
Please Log in or Create an account to join the conversation.
- Polar_Bus
-
- Offline
- User
-

Registered
- Posts: 256
- Thanks: 7
Re: Ring Seating
25 Sep 2012 07:00
I had to do some ex valve guide repair on my Gpz about a year ago, and I decided it would be smart to re-ring while the head was off. My mechanic commented I will need about a good 1500 miles for the rings to seal. He was right, I burned a lot of oil the first 700 miles or so, and now i'm up around 1200 miles, and the oil burning is definately lessening.
Bikes:
'84 GPz1100
'06 HD Fatboy
'84 GPz1100
'06 HD Fatboy
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: Ring Seating
27 Sep 2012 07:52 - 27 Sep 2012 08:05Polar_Bus wrote: I had to do some ex valve guide repair on my Gpz about a year ago, and I decided it would be smart to re-ring while the head was off. My mechanic commented I will need about a good 1500 miles for the rings to seal. He was right, I burned a lot of oil the first 700 miles or so, and now i'm up around 1200 miles, and the oil burning is definately lessening.
:whistle: That's not good.
Larry C.
Last edit: 27 Sep 2012 08:05 by LarryC.
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- Bozo
-
- Offline
- User
-

Registered
- Ride it like u stole it
- Posts: 611
- Thanks: 122
Re: Ring Seating
27 Sep 2012 08:49
RE: smokey engine - Had the same problem many years ago when I thought it would be smart to let someone else do the bore and fit new rings, the bike would smoke under power and basically the compression was crap. Took me a while to work out that the oil scrapper rings (the second from the top, not the oil expander rings) were upside down. If you check the second ring it has a small taper and must be the correct way up to work correctly.
If this is your case, re hone and put new rings in, when I found the problem I thought just turning the rings would be ok, it never was, just used oil and the power was down. Hope this helps.
If this is your case, re hone and put new rings in, when I found the problem I thought just turning the rings would be ok, it never was, just used oil and the power was down. Hope this helps.
First Permanent ride the Z1R since Dec1977 (220,000km) as of June 2015
Second permanent bike 1989 FJ1200 dyno'd 140RWH, great bike.
Third ride is now the Frankenstein 1981 GPZ1100B1, 1983 fully recon motor fitted LOVE THIS BIKE
Forth my work bike FJ1200 1989 (same type as FJ above)
Second permanent bike 1989 FJ1200 dyno'd 140RWH, great bike.
Third ride is now the Frankenstein 1981 GPZ1100B1, 1983 fully recon motor fitted LOVE THIS BIKE
Forth my work bike FJ1200 1989 (same type as FJ above)
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Ring Seating
27 Sep 2012 09:49 - 27 Sep 2012 10:10Did you do a Valve job? Or head work of some kind?lemo32 wrote: yeah, all the above, staggered rings, checked gap, checked piston in bore via feeler guage, all that checked out, also adjusted valves to within .004 on all cyl, did leakdown not leaking at valves, so must be bottom end.
The Leak Down Test you did, was it with gauges? If so what percentage Held out of 100 psi input?
While compression should come up with rings seating, it sounds as though you are low anyway. Did you check it with a second compression gauge, as its possible to have one read low. Are you far above sea level, as this will effect readings?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 27 Sep 2012 10:10 by Motor Head.
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: Ring Seating
27 Sep 2012 15:49
You add oil to the cylinders and the compression only increases by 20 psi? Then your rings are doing an excellent job of sealing, if they weren't then you would have a large increase in psi after adding oil. I've seen over 100 psi increase on worn out rings.
Valves, cam timing, or something else in the head.
Valves, cam timing, or something else in the head.
KD9JUR
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
