Cant get cam timing right, going crazy
- gixxerfiend
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Cant get cam timing right, going crazy
09 Nov 2012 23:22
I have removed and tried to realign these cams at least 15 times and I cant get it right. here is the steps I am taking
1 setting engine to 1-4 tdc by putting it to the line on the left of the T
pulling chain taught
2 install exhaust cam with the line ajoining the t mark just above the the cylinder head facing the front
3 putting the inlet cam facing the rear with exactly 36 pins starting at the exhaust t arrow as 0 and ending at the T arrow on the inlet cam
4 tighten cam hold downs
5 install top sprocket guide
6 install cam chain tensioner, then unloosen the side bolt so the cct tightens the chain
When I first go to turn the motor the 1-4 T on the bottom will move a little bit before the cams do and after a couple of revolutions the inlet is actually just below the surface of the head and exhaust is just above where the gasket would be. Also somewhere around 3-4 markers on the bottom the chain goes loose up top??? Im not an idiot but this is making me feel like one.
1 setting engine to 1-4 tdc by putting it to the line on the left of the T
pulling chain taught
2 install exhaust cam with the line ajoining the t mark just above the the cylinder head facing the front
3 putting the inlet cam facing the rear with exactly 36 pins starting at the exhaust t arrow as 0 and ending at the T arrow on the inlet cam
4 tighten cam hold downs
5 install top sprocket guide
6 install cam chain tensioner, then unloosen the side bolt so the cct tightens the chain
When I first go to turn the motor the 1-4 T on the bottom will move a little bit before the cams do and after a couple of revolutions the inlet is actually just below the surface of the head and exhaust is just above where the gasket would be. Also somewhere around 3-4 markers on the bottom the chain goes loose up top??? Im not an idiot but this is making me feel like one.
2006 GSXR 1000
2005 CBR 600rr
1977 KZ 650
2005 CBR 600rr
1977 KZ 650
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: Cant get cam timing right, going crazy
10 Nov 2012 00:22
Picture?
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- gixxerfiend
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: Cant get cam timing right, going crazy
10 Nov 2012 00:32Attachment inletcam.jpg not found
Attachment exhaustcam.jpg not found
2006 GSXR 1000
2005 CBR 600rr
1977 KZ 650
2005 CBR 600rr
1977 KZ 650
Please Log in or Create an account to join the conversation.
- gixxerfiend
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: Cant get cam timing right, going crazy
10 Nov 2012 00:37
these were taken at 1-4 tdc , pretty sure the exhaust cam is where it needs to be but the inlet T mark line is just slightly below the head, another tooth up and it would put it at 35 pins and imagine it would be way off. I rotated the motor a couple more times and unloosened the tensioner bolt and it cleared up the slack I had. I cant understand what i am doing wrong here
2006 GSXR 1000
2005 CBR 600rr
1977 KZ 650
2005 CBR 600rr
1977 KZ 650
Please Log in or Create an account to join the conversation.
- 4TheKZ1000
-
- User
-

Public
- Thanks: 0
Re: Cant get cam timing right, going crazy
10 Nov 2012 00:51
1st picture looks like cam bolts are loose.....check torque settings....it is wrong in some manuals....I think its like 7 or 8. dont over torque them as they will stip-out.
Please Log in or Create an account to join the conversation.
- gixxerfiend
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: Cant get cam timing right, going crazy
10 Nov 2012 00:54
yea its loose because I tried to move the cam a bit. but the arrow is at the same position with it tigtened down because the other ones are holding it
2006 GSXR 1000
2005 CBR 600rr
1977 KZ 650
2005 CBR 600rr
1977 KZ 650
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Cant get cam timing right, going crazy
10 Nov 2012 00:54 - 10 Nov 2012 00:56
Assuming the timing advancer is set with the 1/4 "T" mark aligned with the pointer, the photos look like the cam timing is set correctly. I did notice you have installed the top sprocket guide facing the wrong way (the bridge should face forward) but that shouldn't affect the timing. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 10 Nov 2012 00:56 by 650ed.
Please Log in or Create an account to join the conversation.
- gixxerfiend
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: Cant get cam timing right, going crazy
10 Nov 2012 01:02
so it is right? I thought both arrows were supposed to be flush with the head per manual? Ive seen a thread where the exhaust arrow should be flush with the "matting material". and your right it is facing the wrong direction. Ill flip it back around
2006 GSXR 1000
2005 CBR 600rr
1977 KZ 650
2005 CBR 600rr
1977 KZ 650
Please Log in or Create an account to join the conversation.
- gixxerfiend
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: Cant get cam timing right, going crazy
10 Nov 2012 01:07
I cant get a good picture down on the crankshaft but there is a T then a line then an F then a line then a 1.4 I have it on the line right after the T. Its different then whats in the manual for some reason
2006 GSXR 1000
2005 CBR 600rr
1977 KZ 650
2005 CBR 600rr
1977 KZ 650
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Cant get cam timing right, going crazy
10 Nov 2012 01:25 - 10 Nov 2012 01:26
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 10 Nov 2012 01:26 by Patton.
Please Log in or Create an account to join the conversation.
- gixxerfiend
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: Cant get cam timing right, going crazy
10 Nov 2012 01:32
the bronze colored one is the one I have. so I should be on the mark right of the T right? whats the F for?
2006 GSXR 1000
2005 CBR 600rr
1977 KZ 650
2005 CBR 600rr
1977 KZ 650
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Cant get cam timing right, going crazy
10 Nov 2012 01:58gixxerfiend wrote: the bronze colored one is the one I have. so I should be on the mark right of the T right? whats the F for?
the bronze colored one is the one I have. so I should be on the mark right of the T right? Yes.
The T stands for "Top Dead Center" or "TDC," which means the pistons are at their highest positions.
The T mark is used for cam timing.
The F mark is used for ignition timing. (As in when the spark plugs Fire.)
When viewed under a timing light at idle rpm, the F mark is supposed to align with the case mark.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
