WTF 78 KZ1000 kicker

  • Ogcoda
  • Ogcoda's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Killing Everything
  • Posts: 49
  • Thanks: 0

WTF 78 KZ1000 kicker

14 Nov 2012 01:06
#558274
So about a month ago i pulled my bike out of the garage and kicked it over. took a few kicks as usual but started non the less. i take it out this week and go to kick it over and there was almost no resistance.... the kicker can be pushed all the way down with one finger but then springs right back. I had the points cover off to see if the nut was spinning as i kicked it and it would barley spin when kicking it. I checked compression and it pulled alot better numbers then i thought it would. 125 125 130 and 125 I'm kinda lost on what could be going on. Anyone have any ideas?
1978 kz1000 Bobber
2006 MazdaSpeed6

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: WTF 78 KZ1000 kicker

14 Nov 2012 01:11
#558275
You're not by any chance pulling in the clutch lever when kicking are you? Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: WTF 78 KZ1000 kicker

14 Nov 2012 01:24
#558277
Is your clutch adjusted correctly? What weight and type of engine oil being used? If any of the "Car Oils" are used, the friction modifiers are not good on wet plate clutches, making them slip.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: WTF 78 KZ1000 kicker

14 Nov 2012 08:41 - 14 Nov 2012 08:48
#558290
"he kicker can be pushed all the way down with one finger but then springs right back"...
Even with clutch plates/oil/sitcking to loose etc... this seems to me to be something different altogether...

Same time, loosen clutch adjustment and test, simple enough starting place.



Take off you kick start plate insuring spring arm/adjustment is correct, inserted into shaft hole, insetred into encase hole, not broken etc....

Had you / PO ever had this apart for the spring must be installed correctly (spring load orientation) to work correctly.

Off my KZ900 should be exactly as your '78 1000 for ideas but confirm in you manual exact configuration.

NOTE: Z1, KZ900 and up to 1980 KZ 1000 engines ~ 98% the same (other than displacements and some other minor details)....



1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az
Last edit: 14 Nov 2012 08:48 by Old Man Rock.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: WTF 78 KZ1000 kicker

14 Nov 2012 12:59
#558315
Ogcoda wrote: So about a month ago i pulled my bike out of the garage and kicked it over. took a few kicks as usual but started non the less. i take it out this week and go to kick it over and there was almost no resistance.... the kicker can be pushed all the way down with one finger but then springs right back. I had the points cover off to see if the nut was spinning as i kicked it and it would barley spin when kicking it. I checked compression and it pulled alot better numbers then i thought it would. 125 125 130 and 125 I'm kinda lost on what could be going on. Anyone have any ideas?

there seems to be some confusing info here.
if the kicker goes down with no resistance,(crank cant be turning) how can there be 125psi compression? cant see it happening?
if the kicker goes down and the crank bolt under the points cover barely turns how can u have 125 psi ?

i would follow OMRs lead on the kick. seems like its not engaging .
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: WTF 78 KZ1000 kicker

14 Nov 2012 13:35
#558323
i wonder if spring #3 is broken and not letting the cogs engage each other?
spring #11 would still return it but it would not engage.

leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: WTF 78 KZ1000 kicker

14 Nov 2012 14:03
#558326
531blackbanshee wrote: i wonder if spring #3 is broken and not letting the cogs engage each other?
spring #11 would still return it but it would not engage.

leon

that was my first thought too. but then he said he checked the compression??? maybe he used the electric starter for that ??
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: WTF 78 KZ1000 kicker

14 Nov 2012 14:42
#558332
mark1122 wrote:
531blackbanshee wrote: i wonder if spring #3 is broken and not letting the cogs engage each other?
spring #11 would still return it but it would not engage.

leon

that was my first thought too. but then he said he checked the compression??? maybe he used the electric starter for that ??

i am pretty sure that would have been the only way he could have checked the compression,given his current situation.

leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum