top end rebuild ????
- poolboy
-
Topic Author
- Offline
- User
-

Registered
- Posts: 44
- Thanks: 1
top end rebuild ????
19 Nov 2012 17:21
I let this bike sit around for about three years and decided to get it running again. I got it running, with assistance of this great forum. It took forever to get it started, cold as heck. So I decided to do a compression check just to see what else I had to do. Heres the result.
Cyl
1- 2 - 3 - 4
dry 52, 82, 107, 112.
wet 105, 138, 148, 164.
no wonder I had a hard time starting this bike :S
Does this look like a valve job, and rings. What do you think ????
Cyl
1- 2 - 3 - 4
dry 52, 82, 107, 112.
wet 105, 138, 148, 164.
no wonder I had a hard time starting this bike :S
Does this look like a valve job, and rings. What do you think ????
1980 KZ750H ,WG's carb rebuild, V&H 4-1 Exh ,WG wiremod, Dyna 3.0 ohm coils, Dyna-S EI DS2-2,New Bridgestones, O-ring Chain,
Please Log in or Create an account to join the conversation.
- 4TheKZ1000
-
- User
-

Public
- Thanks: 0
Re: top end rebuild ????
19 Nov 2012 17:26 - 19 Nov 2012 17:30
rings can and will stick after sitting for that amount of time.....could take some riding or running the bike to free them up....
did you take all plugs out during comp test?
did you have throttle wide open during comp test?
did you take all plugs out during comp test?
did you have throttle wide open during comp test?
Last edit: 19 Nov 2012 17:30 by 4TheKZ1000.
Please Log in or Create an account to join the conversation.
- OldSchoolZ
-
- Offline
- User
-

Registered
- Posts: 217
- Thanks: 33
Re: top end rebuild ????
19 Nov 2012 21:00
Before you tear it down, look at the valve clearance.
Remember, don't work on your bike so much you never ride it.
The following user(s) said Thank You: poolboy
Please Log in or Create an account to join the conversation.
- poolboy
-
Topic Author
- Offline
- User
-

Registered
- Posts: 44
- Thanks: 1
Re: top end rebuild ????
19 Nov 2012 22:25 - 19 Nov 2012 22:36
I had the plugs out for the test, did not have the throttle wide open during comp test.
I did not know wide open throttle was necessary during comp test, and please explain why that is necessary.
By the way, please understand I'm not a mechanic by any means. I've done a lot of mechanical work, but that does not qualify me as knowing a damn thing. I admire people who are qualified and certified in the field they hold.
I did not know wide open throttle was necessary during comp test, and please explain why that is necessary.
By the way, please understand I'm not a mechanic by any means. I've done a lot of mechanical work, but that does not qualify me as knowing a damn thing. I admire people who are qualified and certified in the field they hold.
1980 KZ750H ,WG's carb rebuild, V&H 4-1 Exh ,WG wiremod, Dyna 3.0 ohm coils, Dyna-S EI DS2-2,New Bridgestones, O-ring Chain,
Last edit: 19 Nov 2012 22:36 by poolboy. Reason: thought of more stuff to say.
Please Log in or Create an account to join the conversation.
- poolboy
-
Topic Author
- Offline
- User
-

Registered
- Posts: 44
- Thanks: 1
Re: top end rebuild ????
19 Nov 2012 22:28
I will look at valve clearance before tear down. Thanks
1980 KZ750H ,WG's carb rebuild, V&H 4-1 Exh ,WG wiremod, Dyna 3.0 ohm coils, Dyna-S EI DS2-2,New Bridgestones, O-ring Chain,
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: top end rebuild ????
20 Nov 2012 02:36In order for air to be compressed when inside the combustion chamber, air must first be sucked into the combustion chamber.poolboy wrote: I had the plugs out for the test, did not have the throttle wide open during comp test.
I did not know wide open throttle was necessary during comp test, and please explain why that is necessary....
The supply of air for being sucked into the combustion chamber flows through the carbs.
If the carbs throttle slides are closed down, the air can't flow through the carbs, whereby there's no air sucked into the combustion chamber, and therefore no air to compress.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
The following user(s) said Thank You: Humenik
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: top end rebuild ????
20 Nov 2012 02:41
How did it run before being parked?
If it ran good before maybe try dumping just a little trans fluid mixed with gas down the plug holes and let it sit and work on the rings for a while,youve got nothing to lose
If it ran good before maybe try dumping just a little trans fluid mixed with gas down the plug holes and let it sit and work on the rings for a while,youve got nothing to lose
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- poolboy
-
Topic Author
- Offline
- User
-

Registered
- Posts: 44
- Thanks: 1
Re: top end rebuild ????
20 Nov 2012 23:04
Wow, I did another comp test today and the results were dramatic.
Heres results for todays test.
cyl 1 2 3 4
old test
dry 52 82 107 112
wet throttle closed 105 138 148 164
todays test
wet throttle wide open 116 178 205 235
heck of a difference guys.
I can see why having an open throttle is important.
It ran good before I parked it 3 years ago wireman.
Thanks Mr Patton for the explanation, I read your articles a lot, thanks.
And 4TheKZ1000 , I did have the plugs out during test.
OldSchoolZ, I will look at valve clearance before I tear it apart.
I will try wiremans advice and soak it with trans fluid and gas.
Thanks guys for the advice, I will follow it.
I'll post again soon.
Heres results for todays test.
cyl 1 2 3 4
old test
dry 52 82 107 112
wet throttle closed 105 138 148 164
todays test
wet throttle wide open 116 178 205 235
heck of a difference guys.
I can see why having an open throttle is important.
It ran good before I parked it 3 years ago wireman.
Thanks Mr Patton for the explanation, I read your articles a lot, thanks.
And 4TheKZ1000 , I did have the plugs out during test.
OldSchoolZ, I will look at valve clearance before I tear it apart.
I will try wiremans advice and soak it with trans fluid and gas.
Thanks guys for the advice, I will follow it.
I'll post again soon.
1980 KZ750H ,WG's carb rebuild, V&H 4-1 Exh ,WG wiremod, Dyna 3.0 ohm coils, Dyna-S EI DS2-2,New Bridgestones, O-ring Chain,
The following user(s) said Thank You: 4TheKZ1000
Please Log in or Create an account to join the conversation.
- 4TheKZ1000
-
- User
-

Public
- Thanks: 0
Re: top end rebuild ????
20 Nov 2012 23:34poolboy wrote: Wow, I did another comp test today and the results were dramatic.
Heres results for todays test.
cyl 1 2 3 4
old test
dry 52 82 107 112
wet throttle closed 105 138 148 164
todays test
wet throttle wide open 116 178 205 235
heck of a difference guys.
I can see why having an open throttle is important.
It ran good before I parked it 3 years ago wireman.
Thanks Mr Patton for the explanation, I read your articles a lot, thanks.
And 4TheKZ1000 , I did have the plugs out during test.
OldSchoolZ, I will look at valve clearance before I tear it apart.
I will try wiremans advice and soak it with trans fluid and gas.
Thanks guys for the advice, I will follow it.
I'll post again soon.
There are so bright guys on here about KZ issues....use and abuse them..... :woohoo: :woohoo: :woohoo:
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
