changed headgasket and now wont start ...???
- andyvr4
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
changed headgasket and now wont start ...???
28 Nov 2012 22:55
Hi I have a 1983 kz750 Ltd h4 chain drive. And I just replaced the headgasket and put it all back together and now it doesn't start. I think its my timing I lined up the z7ex with the head on the exhaust cam and counted 45-46 teeth and put the in, between 44-43 cause it looks like the picture. But it says to put it at 45-46 teeth but I'm afraid ill mess up a valve. And i did this all at t1 notch next to f1f4.
1983 kz750 Ltd 4 cyl.
Andy
Andy
Please Log in or Create an account to join the conversation.
- 4TheKZ1000
-
- User
-

Public
- Thanks: 0
Re: changed headgasket and now wont start ...???
28 Nov 2012 23:27 - 28 Nov 2012 23:48
sorry but looks like you may have damaged her.
Timing must have been off. Just a few teeth off on chain or cam oriention wrong and a valve can come into contact with the piston.
I would guess no noise if you try to start...like backfire or any sign of bike turning over or tring to run?
I would try to correct timming first, this can keep further damage from happing if any at all.
Then if bike turns over a compression check would be in order. If that is ok the valves are fine.
Timing must have been off. Just a few teeth off on chain or cam oriention wrong and a valve can come into contact with the piston.
I would guess no noise if you try to start...like backfire or any sign of bike turning over or tring to run?
I would try to correct timming first, this can keep further damage from happing if any at all.
Then if bike turns over a compression check would be in order. If that is ok the valves are fine.
Last edit: 28 Nov 2012 23:48 by 4TheKZ1000.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: changed headgasket and now wont start ...???
29 Nov 2012 03:21
what's the compression read?
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- andyvr4
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: changed headgasket and now wont start ...???
29 Nov 2012 10:00
Haven't done a compression test yet will today. But was all at 120 before head gasket change. It did backfire after a couple of cranks. But did not start. I turned the engine over by wrench a few times before start and there was no tapping. All quiet. And even cranking no tapping. Also before all this I did the dynojet kit install and this is the first attempt to start it.
1983 kz750 Ltd 4 cyl.
Andy
Andy
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: changed headgasket and now wont start ...???
29 Nov 2012 11:16 - 29 Nov 2012 11:21
On some models it's possible to install the timing advancer rotor 180° out.
When the pointer (stock igniter) or embedded magnet (Dyna-S) passes by the left-side pickup module, it ungrounds whichever ignition coil is connected to the left-side pickup module, which causes the ignition coil to fire.
When the pointer (stock igniter) or embedded magnet (Dyna-S) passes by the right-side pickup module, it ungrounds whichever ignition coil is connected to the right-side pickup module, which causes the ignition coil to fire.
Good Fortune!
When the pointer (stock igniter) or embedded magnet (Dyna-S) passes by the left-side pickup module, it ungrounds whichever ignition coil is connected to the left-side pickup module, which causes the ignition coil to fire.
When the pointer (stock igniter) or embedded magnet (Dyna-S) passes by the right-side pickup module, it ungrounds whichever ignition coil is connected to the right-side pickup module, which causes the ignition coil to fire.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 29 Nov 2012 11:21 by Patton.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: changed headgasket and now wont start ...???
29 Nov 2012 11:25
If needed -- wiring diagram from FILEBASE:
Click > www.kzrider.com/filebase/doc_download/317-z750h4
Good Fortune!
Click > www.kzrider.com/filebase/doc_download/317-z750h4
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- andyvr4
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: changed headgasket and now wont start ...???
29 Nov 2012 13:17
Thank you ill check this out also
1983 kz750 Ltd 4 cyl.
Andy
Andy
Please Log in or Create an account to join the conversation.
- andyvr4
-
Topic Author
- Offline
- User
-

Registered
- Posts: 38
- Thanks: 0
Re: changed headgasket and now wont start ...???
29 Nov 2012 23:31
It was my timing got it right now, now I just need to get my jets situated thank you for the help
1983 kz750 Ltd 4 cyl.
Andy
Andy
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
