Piston ring gaps

  • 3cav84a
  • 3cav84a's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 47
  • Thanks: 3

Piston ring gaps

15 Dec 2012 23:13 - 15 Dec 2012 23:14
#563146
G'day, I have taken the rings off the pistons and have measured the gaps with the rings being inserted into the bore as the Kawasaki manual says to do on page 151 (1977 KZ 1000). In table H26 it says the gap should be between 0.04-0.08 for the top ring and 0.03-0.07 for the 2nd ring. Is this fair dinkum or is this a misprint. I can believe 0.4-0.8 of a millimeter but not 4 one hundreths of a millimeter. Maybe I am wrong and all the rings are worn and need replacing because all of my measurements are around the 0.3-0.6 mm. Any ideas, regards Neil
1977 KZ 1000 A1
Last edit: 15 Dec 2012 23:14 by 3cav84a.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Piston ring gaps

16 Dec 2012 00:03
#563153
3cav84a wrote: G'day, I have taken the rings off the pistons and have measured the gaps with the rings being inserted into the bore as the Kawasaki manual says to do on page 151 (1977 KZ 1000). In table H26 it says the gap should be between 0.04-0.08 for the top ring and 0.03-0.07 for the 2nd ring. Is this fair dinkum or is this a misprint. I can believe 0.4-0.8 of a millimeter but not 4 one hundreths of a millimeter. Maybe I am wrong and all the rings are worn and need replacing because all of my measurements are around the 0.3-0.6 mm. Any ideas, regards Neil

Perhaps confusing H26 groove clearance with H29 end-gap clearance

Note thickness gauge for H26 is between piston-land and side of ring.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • 3cav84a
  • 3cav84a's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 47
  • Thanks: 3

Re: Piston ring gaps

16 Dec 2012 00:07
#563155
Thanks just went out to shed and saw the error of my ways, thanks
1977 KZ 1000 A1

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Piston ring gaps

16 Dec 2012 22:03 - 16 Dec 2012 22:07
#563302
3cav84a wrote: G'day, I have taken the rings off the pistons and have measured the gaps with the rings being inserted into the bore as the Kawasaki manual says to do on page 151 (1977 KZ 1000). In table H26 it says the gap should be between 0.04-0.08 for the top ring and 0.03-0.07 for the 2nd ring. Is this fair dinkum or is this a misprint. I can believe 0.4-0.8 of a millimeter but not 4 one hundreths of a millimeter. Maybe I am wrong and all the rings are worn and need replacing because all of my measurements are around the 0.3-0.6 mm. Any ideas, regards Neil
It's easy to estimate: nominal ring end gap is always in the ball park of .003" - .004" per inch of bore diameter. Sorry that's not in metric, but it's right. The maximum limit number is probably about twice that.
all of my measurements are around the 0.3-0.6 mm. Any ideas, regards Neil
I think that would be about .012" - .024" which is probably in spec.
1979 KZ-750 Twin
Last edit: 16 Dec 2012 22:07 by bountyhunter.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum