Need some help with my engine rebuild

  • Sidecar
  • Sidecar's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 2
  • Thanks: 0

Need some help with my engine rebuild

04 May 2013 00:18
#585560
I just started rebuilding a 78 kz1000 that was given to me by my father. I planned on redoing everything on the bike since i have a a newer bike that i can ride while this one is being worked on. So i started by by taking everything apart and tearing apart the engine. One thing i was told was that the engine had a big bore kit put in it before my father purchased it. So my first problem is help identifying the piston that was used in it. i measured the pistons and they appear to be 72mm, so i've already determined that it should be a 1075 kit as opposed to the 1200 kit he was told was in it. but i was hoping someone on here can help identify the manufacture so i can get new piston rings for it, the only identification mark i've found on it was on the bottom side of the piston which was 4025, not sure if thats anything or just a production number. the second problem i have is that when i was disassembling the engine i found what appeared to be melted plastic around where the cam chain rides. the issue is that i can't find anything that appears to be missing or bad that would cause this. its not really a big deal since i plan on replacing a lot of the cam gears and guides that seam to be worn and hard, which is pretty much everything. i've attached a couple of pictures of the pistons, unfortunately i didn't take any pictures of the melted plastic before i cleaned it out


Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Need some help with my engine rebuild

04 May 2013 00:31
#585565
Is there a w anyplace inside of pistons? :)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • Powerstroke_fan
  • Powerstroke_fan's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1020
  • Thanks: 90

Re: Need some help with my engine rebuild

04 May 2013 08:03 - 04 May 2013 08:04
#585584
Maybe the melted plastic/rubber you seen was the little dampner blocks that sit on each side of the cam chain idler gears.
1977 KZ 1000 work in progress
Last edit: 04 May 2013 08:04 by Powerstroke_fan.

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: Need some help with my engine rebuild

04 May 2013 08:27
#585588
Looks like an old Wiseco piston. The number on the wrist pin boss might buy you something....
Larry C.

Please Log in or Create an account to join the conversation.

  • Kraz1
  • Kraz1's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 394
  • Thanks: 30

Re: Need some help with my engine rebuild

05 May 2013 02:05
#585730
You might be looking to see if No.#12 is still screwed in place, and in the correct shape at the front of the Cylinder Block.


Please Log in or Create an account to join the conversation.

  • Sidecar
  • Sidecar's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 2
  • Thanks: 0

Re: Need some help with my engine rebuild

05 May 2013 19:18
#585829
Thanks for all the advise, I checked the pistons a little more and found that there is another mark on the other boss, but there is an hole drilled right through it on all of them, one of the them appears to be half of a w in a circle, as far as the plastic, all the idler dampener blocks seem to be whole and accounted for, and the guide was there and the correct shape, but did have some grooves worn in it, since it appears to be limited to the cam area, I'm gonna try and replace as many pieces add I can find

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Need some help with my engine rebuild

05 May 2013 22:48
#585871
The w in the circle stands for wiseco :)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum