81 gpz injectors
- pstrbrc
-
Topic Author
- Offline
- User
-

Registered
- '81 GPz 1100 project
- Posts: 355
- Thanks: 9
81 gpz injectors
30 Jul 2006 16:27
OK, I know there's still quite a few gpz's out there with the FI working, so somebody's got to know this answer.
What are the specs on the '81 injectors? What is the flow rating? Looking at them, they are very close to the standard Bosch, with the exception of the mounting collar, and the barb top, instead of the standard Bosch o-ring setup for a fuel rail. But looking at the nose of the injectors, a standard Bosch should fit.
My concern with finding different injectors for my bike is three-fold-
1. These injectors have sat for 16 years. Can't be good.
2. OEM replacements are $316 each through BikeBandit, and I don't find any other source. None are available through an E-Bay merchant, for example.
3. (and, the most important to this hotrodder) When I parked this bike, it was as much because it had limited hotrodding potential, since the word was that the factory injectors were at the limit of their duty cycle, and couldn't flow any more gas, so a big-bore kit, camshafts, etc. were not much good.
Now that I've come accross the MegaSquirt ecu, I'm aware that I can put larger injectors on it and tune it right, so, for instance, the ubiquitous Ford 19# injector (that I just got 16 of for $30 on E-Bay) will support 130 HP.
So, does anybody have experience with changing injectors on this bike?
Any info will be appreciated.
Bruce
What are the specs on the '81 injectors? What is the flow rating? Looking at them, they are very close to the standard Bosch, with the exception of the mounting collar, and the barb top, instead of the standard Bosch o-ring setup for a fuel rail. But looking at the nose of the injectors, a standard Bosch should fit.
My concern with finding different injectors for my bike is three-fold-
1. These injectors have sat for 16 years. Can't be good.
2. OEM replacements are $316 each through BikeBandit, and I don't find any other source. None are available through an E-Bay merchant, for example.
3. (and, the most important to this hotrodder) When I parked this bike, it was as much because it had limited hotrodding potential, since the word was that the factory injectors were at the limit of their duty cycle, and couldn't flow any more gas, so a big-bore kit, camshafts, etc. were not much good.
Now that I've come accross the MegaSquirt ecu, I'm aware that I can put larger injectors on it and tune it right, so, for instance, the ubiquitous Ford 19# injector (that I just got 16 of for $30 on E-Bay) will support 130 HP.
So, does anybody have experience with changing injectors on this bike?
Any info will be appreciated.
Bruce
\'81 GPz 1100 project
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: 81 gpz injectors
30 Jul 2006 19:28
I have no experience with GPz1100's, but most injectors will interchange, I think they are a standard size (not flow rate, just mounting).
There is a whole bunch of injector info on www.msefi.com/forums/index.php , the MegaSquirt site. There should be numbers on the injectors that you can use to look up the specs, just check the "OEM EFI Hardware forum and the Injector forum on the MS site.
There is a whole bunch of injector info on www.msefi.com/forums/index.php , the MegaSquirt site. There should be numbers on the injectors that you can use to look up the specs, just check the "OEM EFI Hardware forum and the Injector forum on the MS site.
KD9JUR
Please Log in or Create an account to join the conversation.
- Lorcan
-
- Offline
- User
-

Registered
- Speed Loony
- Posts: 580
- Thanks: 60
Re: 81 gpz injectors
01 Aug 2006 05:12
The GPz1100 uses low impedance injectors which are (I think) about 10% smaller than the ones on the 750 turbo. The reason they run out of duty cycle is that the 1100 fires them every revolution, instead of every other rev on the turbo. I would think they would be ok for 180hp or so if fired this way.
You can indeed fit any other Bosch style injector, I have had several sizes in my bikes, but am I right in saying that the B1 models have the injectors mounted directly in the head and not in the throttle bodies? If so, those models had a problem with the injectors overheating. If that's the case you might be better off with some later model 1100 throttle bodies and to blank off the original holes for the injectors. I think the Megasquirt can handle either high or low impedance injectors, or you could do what I did and fit high impedance injectors and a Powercommander, which has the benefit of easy mapping at any Dynojet tuning centre as they are familiar with the software. Instructions for doing this are on my site.
You can indeed fit any other Bosch style injector, I have had several sizes in my bikes, but am I right in saying that the B1 models have the injectors mounted directly in the head and not in the throttle bodies? If so, those models had a problem with the injectors overheating. If that's the case you might be better off with some later model 1100 throttle bodies and to blank off the original holes for the injectors. I think the Megasquirt can handle either high or low impedance injectors, or you could do what I did and fit high impedance injectors and a Powercommander, which has the benefit of easy mapping at any Dynojet tuning centre as they are familiar with the software. Instructions for doing this are on my site.
760cc - 8.69@162mph
810cc, 211mph www.750turbo.com
www.stormdragbike.com
810cc, 211mph www.750turbo.com
www.stormdragbike.com
Please Log in or Create an account to join the conversation.
- Dave Sloan
-
- Offline
- User
-

Registered
- Posts: 239
- Thanks: 3
Re: 81 gpz injectors
01 Aug 2006 17:23
Yes Lorcan is right the mega squirt can handle low or high imp injectors, I have read that low imp can be used in conjuntion with resistors or using the flyback circuit.
Cheers
DAve
Cheers
DAve
Z650B2 - Injected
Please Log in or Create an account to join the conversation.
- pstrbrc
-
Topic Author
- Offline
- User
-

Registered
- '81 GPz 1100 project
- Posts: 355
- Thanks: 9
Re: 81 gpz injectors
02 Aug 2006 05:51
Actually, it looks like the heat problem with the injectors was caused by the use of the old style pintle caps, which used a square section o-ring all the way up on the shoulder of the pintle, exposing the entire pintle to engine heat. (far right in this picture)
I'll be boring the injector holes out so injectors with 14mm round-section o-rings will fit. (center) I've also got some work to do to change from the barb top on the stock injectors to the o-ring top that's common on most domestic injectors. That should be fun! Looking at a shop manual, Kawasaki made these changes themselves when they moved the injectors from the head to the throttle body in '82. But an '81 I have, and an '81 I'll use. I'll post pics when I get it done.
I'll be boring the injector holes out so injectors with 14mm round-section o-rings will fit. (center) I've also got some work to do to change from the barb top on the stock injectors to the o-ring top that's common on most domestic injectors. That should be fun! Looking at a shop manual, Kawasaki made these changes themselves when they moved the injectors from the head to the throttle body in '82. But an '81 I have, and an '81 I'll use. I'll post pics when I get it done.
\'81 GPz 1100 project
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Please Log in or Create an account to join the conversation.
- Lorcan
-
- Offline
- User
-

Registered
- Speed Loony
- Posts: 580
- Thanks: 60
Re: 81 gpz injectors
02 Aug 2006 06:12
No, the 82-85 injectors are all the same as the ones on the right, with barb/hose top mounts. They are fine when mounted in the throttle bodies.
760cc - 8.69@162mph
810cc, 211mph www.750turbo.com
www.stormdragbike.com
810cc, 211mph www.750turbo.com
www.stormdragbike.com
Please Log in or Create an account to join the conversation.
- pstrbrc
-
Topic Author
- Offline
- User
-

Registered
- '81 GPz 1100 project
- Posts: 355
- Thanks: 9
Re: 81 gpz injectors
02 Aug 2006 09:12
Well, that's good to know. I was thinking that it might be less work to find myself an '82 head and throttle bodies, so I wouldn't have to do any serious modifying to fit 19# Ford injectors. But if the '82 used the same injectors as my '81, I'd still have to modify.
There's no point contiuing to use the original style injectors when I have the range of choices in the current style.
Thanks, everybody, for your input!
There's no point contiuing to use the original style injectors when I have the range of choices in the current style.
Thanks, everybody, for your input!
\'81 GPz 1100 project
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Please Log in or Create an account to join the conversation.
- jydog
-
- Offline
- User
-

Registered
- Posts: 300
- Thanks: 9
Re: 81 gpz injectors
30 Aug 2011 21:41
Did you end up using the Ford injectors? If so where there any modifications you had to do?
81 KZ1000 LTD
Griffin GA
Griffin GA
Please Log in or Create an account to join the conversation.
- jydog
-
- Offline
- User
-

Registered
- Posts: 300
- Thanks: 9
Last edit: 09 Sep 2011 06:23 by jydog.
Please Log in or Create an account to join the conversation.
- 9am53
-
- Offline
- User
-

Registered
- homebrew, and some bbq
- Posts: 1787
- Thanks: 3
Re: 81 gpz injectors
09 Sep 2011 08:12
wow, that is a ressurection of biblical proportions!
'84 GPz900r
'71 CB350
s289.photobucket.com/albums/ll231/9am53/
'71 CB350
s289.photobucket.com/albums/ll231/9am53/
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: 81 gpz injectors
09 Sep 2011 08:20
havent seen preacher on here in years! :laugh:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- ELCouz
-
- Offline
- User
-

Registered
- Posts: 376
- Thanks: 5
Re: 81 gpz injectors
14 Sep 2011 11:34
thanks for the find, i have a 81 gpz 1100 efi... maybe its a resurrection from the graveyard but its useful
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
