Is this piston reusable?
- polkat
-
Topic Author
- Offline
- User
-

Registered
- Posts: 513
- Thanks: 1
Is this piston reusable?
08 Feb 2010 00:04 - 08 Feb 2010 00:18
Rebuilding my 750-four engine. Took the pistons out today. Both the pistons and bores (which are stock size-probably originals) are in spec with the factory numbers, and the bores and pistons look just fine....except for piston #4. Here is a lousy pic of that piston showing some of the skuffing near the piston pin boss.....
This piston is scuffed on three sides 90 degrees apart (but not on the forth side). Oddly, the bore shows nothing in these areas (which measure out fine). The skuffing on the piston looks bad, but won't catch a fingernail. I'm poor, and so I'm wondering if I can reuse this piston? Or should I look for a reusable used one (anyone got one)?
Thanks!
This piston is scuffed on three sides 90 degrees apart (but not on the forth side). Oddly, the bore shows nothing in these areas (which measure out fine). The skuffing on the piston looks bad, but won't catch a fingernail. I'm poor, and so I'm wondering if I can reuse this piston? Or should I look for a reusable used one (anyone got one)?
Thanks!
Last edit: 08 Feb 2010 00:18 by polkat.
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: Is this piston reusable?
08 Feb 2010 05:27
I hate to say that piston looks pretty bad. That piston looks more than scuffed. If any of the others look anywhere as close I would replace all of them. The question is; What do the cylinders look like. If you can remove any apparent scuffing with 4-5 swipes of a hone than I say they are OK if it takes much more than that, you will require to have them bored.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Please Log in or Create an account to join the conversation.
- BSKZ650
-
- Offline
- User
-

Registered
- Posts: 2061
- Thanks: 14
Re: Is this piston reusable?
08 Feb 2010 05:39
got to agree with otakar, with that many socres on th piston I dont se any way that the cyl is 1, not going to be scratched, and 2 that it is going to be round.
new set of oversize pistons and rings, and bore cyls out, build it right the first time.
new set of oversize pistons and rings, and bore cyls out, build it right the first time.
77 kz650, owned for over 25 years
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
Please Log in or Create an account to join the conversation.
- 9am53
-
- Offline
- User
-

Registered
- homebrew, and some bbq
- Posts: 1787
- Thanks: 3
Re: Is this piston reusable?
08 Feb 2010 05:56 - 08 Feb 2010 06:05
I noticed Z1E has 199$ cb750 complete oversize piston kits, would he be able to use them?
www.z1enterprises.com/SearchResult.aspx?All=True&KeyWords=impk
www.z1enterprises.com/SearchResult.aspx?All=True&KeyWords=impk
'84 GPz900r
'71 CB350
s289.photobucket.com/albums/ll231/9am53/
'71 CB350
s289.photobucket.com/albums/ll231/9am53/
Last edit: 08 Feb 2010 06:05 by 9am53.
Please Log in or Create an account to join the conversation.
- polkat
-
Topic Author
- Offline
- User
-

Registered
- Posts: 513
- Thanks: 1
Re: Is this piston reusable?
08 Feb 2010 13:21
I'll try to get a better pic. The piston is not as bad as the pic shows (there are reflections in the piston that look like further scuffing).
Surprisingly, as I said, there are no markings in the bore! And the clearance (which should be .040~.067mm) is correct at about .050 all around the piston. Also, the scuffing cannot be felt with a finger. I can't afford new pistons (let alone a single one), so I was wondering about reusing it.
Surprisingly, as I said, there are no markings in the bore! And the clearance (which should be .040~.067mm) is correct at about .050 all around the piston. Also, the scuffing cannot be felt with a finger. I can't afford new pistons (let alone a single one), so I was wondering about reusing it.
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: Is this piston reusable?
08 Feb 2010 13:38
What ever you do, do not use any kind of abrasive pad to clean the side walls.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Please Log in or Create an account to join the conversation.
- kpier998
-
- Offline
- User
-

Registered
- Posts: 117
- Thanks: 1
Re: Is this piston reusable?
08 Feb 2010 14:13
Does anyone know if this will build up a piston skirt and fill in any imperfections:
www.swaintech.com/store.asp?pid=10971
One of the guys on another forum mentioned this place some years ago. Maybe it would be worthwhile to contact them and send a pic of that piston to see what they can do. For instance, it is only 15 to 20 bucks for the skirt coating.
www.swaintech.com/store.asp?pid=10971
One of the guys on another forum mentioned this place some years ago. Maybe it would be worthwhile to contact them and send a pic of that piston to see what they can do. For instance, it is only 15 to 20 bucks for the skirt coating.
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: Is this piston reusable?
08 Feb 2010 14:40 - 08 Feb 2010 16:07
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Last edit: 08 Feb 2010 16:07 by Tony. Reason: please contact KZrider.com if you want to advertise.
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: Is this piston reusable?
08 Feb 2010 14:41
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Please Log in or Create an account to join the conversation.
- hardr0ck68
-
- Offline
- User
-

Registered
- Who put the what in the where?
- Posts: 798
- Thanks: 3
Re: Is this piston reusable?
08 Feb 2010 14:43
cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll...e=STRK%3AMESELX%3AIT
This is my auction, those pistons are in great shape. I also have the cylinder sleeves they were used in (however the sleeves have been removed from the block).
I would be saving these pistons for spares if I did not need the space.
This is my auction, those pistons are in great shape. I also have the cylinder sleeves they were used in (however the sleeves have been removed from the block).
I would be saving these pistons for spares if I did not need the space.
1977 kz650 c1
bought it because I was told it would never run again...I like to prove people wrong.
bought it because I was told it would never run again...I like to prove people wrong.
Please Log in or Create an account to join the conversation.
- nads.com
-
- Offline
- User
-

Registered
- Posts: 993
- Thanks: 20
Re: Is this piston reusable?
08 Feb 2010 14:50
If the piston is round i would use it. I use 220 sandpaper to remove any aluminum and then sand crossways for some oil retention, steel whool will final polish and remove any remaining aluminum deposits. I've never had a problem with this and you have good bores, which is the key to a tight bore when it's re-installed. That engine isn't going to know any difference.
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: Is this piston reusable?
08 Feb 2010 14:51
hardr0ck68 wrote:
The only problem is that yours are for a 650 and his are a 750.
cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll...e=STRK%3AMESELX%3AIT
This is my auction, those pistons are in great shape. I also have the cylinder sleeves they were used in (however the sleeves have been removed from the block).
I would be saving these pistons for spares if I did not need the space.
The only problem is that yours are for a 650 and his are a 750.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
