Clutch cable promblems! Help!
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Clutch cable promblems! Help!
10 Mar 2011 08:20
Hey guys just joined the site, from jersey here. heres my problem. under the sprocket cover of my 79 ltd400 the clutch lifter assmebly i cant get to sit right i dont think, meaning... when i pull the lever i hear a pop and open the cover back up and the lifter assembly wont return...what could it be? i just ordered a new cable but i doubt thats what it is, i got the bike from orig owner with only 1800 miles on it. please any help is greatly appreciated i looked at the manual and did everything it said.
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Clutch cable promblems! Help!
10 Mar 2011 10:50 - 10 Mar 2011 10:51
Are you certain that the sprocket cover is completely seated and snug?
Have you inspected the device itself? Maybe it isnt working properly?
Maybe the cable is not seating properly at the device/rod pusher?
Make sure to perform the clutch adjustment on the cover, before tightening any other clutch cable adjustments. Loosen the nut, then turn the slotted adjuster out completely, then in until it stops lightly/very little pressure, then back it of 1/8th turn and tighten the nut.
I like to adjsut the sprocket cover/pushrod adjustment, then set the cable at the handlebar to about 1/8th inch gap, then adjsut the rest at the cable center adjustment.
Fine tune with handlebar aduster later.
Good luck.
Have you inspected the device itself? Maybe it isnt working properly?
Maybe the cable is not seating properly at the device/rod pusher?
Make sure to perform the clutch adjustment on the cover, before tightening any other clutch cable adjustments. Loosen the nut, then turn the slotted adjuster out completely, then in until it stops lightly/very little pressure, then back it of 1/8th turn and tighten the nut.
I like to adjsut the sprocket cover/pushrod adjustment, then set the cable at the handlebar to about 1/8th inch gap, then adjsut the rest at the cable center adjustment.
Fine tune with handlebar aduster later.
Good luck.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 10 Mar 2011 10:51 by TeK9iNe.
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 11 Feb 2013 13:26 by martin_csr.
Please Log in or Create an account to join the conversation.
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Re: Clutch cable promblems! Help!
10 Mar 2011 13:20
yea i tried adjusting thought i was getting a nice lever and then, POP its just not returning back down i cant figure out why. Its driving me up a wall!1
Please Log in or Create an account to join the conversation.
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Re: Clutch cable promblems! Help!
10 Mar 2011 13:24
the spring cant be causing something like this right?
Please Log in or Create an account to join the conversation.
- johnbgood
-
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 4
Re: Clutch cable promblems! Help!
10 Mar 2011 13:26
Hi
on my KZ1000 the clutch adjuster has a small plate with 3 "bearings" with a flat spot on it. If the flat spot isn't lined up properly when being installed you get a "false adjustment. Pull the clutch lever and it just loosens up.
Not sure how your is set up.
regards
John
on my KZ1000 the clutch adjuster has a small plate with 3 "bearings" with a flat spot on it. If the flat spot isn't lined up properly when being installed you get a "false adjustment. Pull the clutch lever and it just loosens up.
Not sure how your is set up.
regards
John
KZ1000P 1991
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Clutch cable promblems! Help!
10 Mar 2011 13:31
martin_csr wrote:
Yes --- some of the service manuals are reportedly incorrect or misleading.
As martin suggested, would re-adjust by turning the screw in the opposite directions.
Good Fortune!
...When doing the clutch adjustment, did you turn the adjusting screw in the correct direction? On some models, like my 81 650, it's turned counterclockwise first until it's tight, then 1/4 turn clockwise. On other models it's the opposite: clockwise first until tight, then you back it out a tad.
Yes --- some of the service manuals are reportedly incorrect or misleading.
As martin suggested, would re-adjust by turning the screw in the opposite directions.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Clutch cable promblems! Help!
10 Mar 2011 13:36
khawk912 wrote:
Not uncommon.
If incorrectly adjusted, the POP may result from overwhelming the adjustment assembly.
Good Fortune!
yea i tried adjusting thought i was getting a nice lever and then, POP its just not returning back down i cant figure out why....
Not uncommon.
If incorrectly adjusted, the POP may result from overwhelming the adjustment assembly.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Re: Clutch cable promblems! Help!
10 Mar 2011 13:40
UPDATE!!
i got a clutch lever but hten just adjusted it too much and pop again, then stripped the bottom screw by the footpeg like an idiot.
Anyway, even though i had the lever i still couldnt roll it if it was in first gear? shouldnt i be able to roll it if i pull the clutch?
i got a clutch lever but hten just adjusted it too much and pop again, then stripped the bottom screw by the footpeg like an idiot.
Anyway, even though i had the lever i still couldnt roll it if it was in first gear? shouldnt i be able to roll it if i pull the clutch?
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Clutch cable promblems! Help!
10 Mar 2011 13:55
khawk912 wrote:
Not unless the clutch is actually disengaging.
Not unusual for clutch plates to "drag" on a cold engine or just started engine before the plates are "broken loose."
After the plates are "broken loose," should be able to roll the bike while the transmission's in gear so long as squeezing the handlebar clutch lever is actually disengaging the clutch.
Good Fortune!
...even though i had the lever i still couldnt roll it if it was in first gear? shouldnt i be able to roll it if i pull the clutch?
Not unless the clutch is actually disengaging.
Not unusual for clutch plates to "drag" on a cold engine or just started engine before the plates are "broken loose."
After the plates are "broken loose," should be able to roll the bike while the transmission's in gear so long as squeezing the handlebar clutch lever is actually disengaging the clutch.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- johnbgood
-
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 4
Re: Clutch cable promblems! Help!
10 Mar 2011 14:03
Still sounds like the little plate with the 3 balls.
You have to take the cover off to see. I caused my own problem (how I found out) by turning the screw the wrong way.
You have to take the cover off to see. I caused my own problem (how I found out) by turning the screw the wrong way.
KZ1000P 1991
Please Log in or Create an account to join the conversation.
- johnbgood
-
- Offline
- User
-

Registered
- Posts: 45
- Thanks: 4
Re: Clutch cable promblems! Help!
10 Mar 2011 15:42
How you coming with your clutch issue?
John
John
KZ1000P 1991
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
