nightmare part 8
- allen6634
-
Topic Author
- Offline
- User
-

Registered
- Posts: 48
- Thanks: 0
nightmare part 8
09 Apr 2011 20:44
i have came to the end of my rope today i took my carbs off and found nothing everything looked great as has before , so i thought being that i had the carbs off i should at lest make a change or something ,so i took all the needles out of the carbs , and now the bike runs great ,so i thinking that i have to shim the needles , does anyone know of how many shims i should start with?im thinking 3 i can't find a base line number to go by. i would like to thank everyone for the advice all along.
1983 kz 550 m
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: nightmare part 8
09 Apr 2011 21:41
If you have to use shims, I've read somewhere that #6 thin flat washers will work good for the non adjustable needles in some carbs. Most hardware stores sell them individually for under $.10 each
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 12 Feb 2013 12:23 by martin_csr.
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: nightmare part 8
10 Apr 2011 13:29 - 10 Apr 2011 13:32
You ran the bike with no needles, and it was great??!!!?!!!? Wha, you got some other problem! :laugh:
:laugh: :laugh: :laugh: :laugh: Sooooo true. I need to copy/paste this into the first lines of every question I answer!
PERFORM THE $#%&ING MAINTENENCE CHAPTER! :woohoo: :laugh: :laugh:
Not a dig at you allen6634! Best of luck!
martin_csr wrote: Why not start from scratch, assume you've done everything wrong, then start at the tank and work your way thru the various systems on the motorcycle, checking and setting everything as per the factory manual. And reference the diagrams to make sure nothing is missing.
Do everything as perfectly as you can. Double check each item, then move on to the next.
No factory manual? Get one asap.
:laugh: :laugh: :laugh: :laugh: Sooooo true. I need to copy/paste this into the first lines of every question I answer!
PERFORM THE $#%&ING MAINTENENCE CHAPTER! :woohoo: :laugh: :laugh:
Not a dig at you allen6634! Best of luck!
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 10 Apr 2011 13:32 by TeK9iNe.
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 12 Feb 2013 12:24 by martin_csr.
Please Log in or Create an account to join the conversation.
- allen6634
-
Topic Author
- Offline
- User
-

Registered
- Posts: 48
- Thanks: 0
Re: nightmare part 8
10 Apr 2011 18:40
i have to agree i am learning alot about the bike. if you don't mind look at past posts i have named them 1 is from the first and 8 is where i am today. it is like a scarry novel.lol
1983 kz 550 m
Please Log in or Create an account to join the conversation.
- Zedone
-
- Offline
- User
-

Registered
- Posts: 397
- Thanks: 14
Re: nightmare part 8
11 Apr 2011 06:30
I didn't notice throughout your chapters that you inspected your float valves (unless I overlooked that) sounds to me that your float valves are not working right..... it sounds like your float valves are completely out to lunch. Did you take each one out and check them???? They are VERY delicate (self contained) spring loaded parts that regulate fuel to each bowl..... dirt gets in them and they get stuck at different positions screwing your bowl levels. They are located under the tab of the float itself, you have to remove the float to get at them. Take each one out and press your finger on the end of it and it shd move freely in & out having light to moderate spring tension both ways. You can spray carb cleaner (or WD40) at them and work the crap out of them if they are stuck or not moving smoothly. Make sure they are opening & closing on there own ok by pressing the valve with your finger releasing them. Then reinstall them. If not get new ones.
I'd also pull your gastank, pull the petcock off make DAM SURE theres not crap in there or the tank give it a flush with fresh gas (unless its really bad then your going to have to do the Muratic acid teatment, (do a search here)) install a FRESH fuel filter and NEW CLEAR fuel lines (so you can see if there is clean fuel going to your carbs).
Best of luck to you..... Don't let it get you down this crap happens to all of us...
Regards, Doug
I'd also pull your gastank, pull the petcock off make DAM SURE theres not crap in there or the tank give it a flush with fresh gas (unless its really bad then your going to have to do the Muratic acid teatment, (do a search here)) install a FRESH fuel filter and NEW CLEAR fuel lines (so you can see if there is clean fuel going to your carbs).
Best of luck to you..... Don't let it get you down this crap happens to all of us...
Regards, Doug
1977 KZ1000A1
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
Please Log in or Create an account to join the conversation.
- allen6634
-
Topic Author
- Offline
- User
-

Registered
- Posts: 48
- Thanks: 0
Re: nightmare part 8
11 Apr 2011 10:11
now that you mention it i have checked the float levels as the manual said several times. Now i am thinking that there should be shims on or under my needles a in my carbs so last night i called the guy who first disassembled my carbs (and yet he is still claiming that my jets are to big but i have the recommended jets according to the manual). At current time i have caught the guy in two different lies and i am now working blind. According to the dyna jet kit there should be shims somewhere on or around my needles. Now i am asking uall where and how many shims should be on or under the c clips on my needles.
1983 kz 550 m
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: nightmare part 8
11 Apr 2011 10:40 - 11 Apr 2011 10:43allen6634 wrote: ...i have checked the float levels as the manual said several times....
And if so, what results?
Adjusting "float height" by using upside-down-on-the-work-bench measurement (as described in the FSM) often fails to result in actual fuel levels being within specs.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 11 Apr 2011 10:43 by Patton.
Please Log in or Create an account to join the conversation.
- allen6634
-
Topic Author
- Offline
- User
-

Registered
- Posts: 48
- Thanks: 0
Re: nightmare part 8
11 Apr 2011 12:19
yes clear tube test has been done just like the manual states everything has come within spec , this is why i have called my problem "nightmare" you know i have a problem that isn't listed in any book or any one hasn't before ,now i don't understand why the bike runs so good with the needles out and the bike will only idel with the needels in is there a way i can find some info o.n my carbs
1983 kz 550 m
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: nightmare part 8
11 Apr 2011 12:25
You should go back and read the advice given, POD's are what you have changed. Adding POD's will need an increase in Jet sizes. There are abundant threads on this subject. If your carb's have Vacuum operated slide valves, CV carb's, then it will be that much harder to tune.
My advice is put the stock airbox back in with stock jetting and ride it instead of working on it.
Just my opinion.
My advice is put the stock airbox back in with stock jetting and ride it instead of working on it.
Just my opinion.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- allen6634
-
Topic Author
- Offline
- User
-

Registered
- Posts: 48
- Thanks: 0
Re: nightmare part 8
11 Apr 2011 12:58
my bike has stock air box. i am going to restore it to factory , back in the day i luved the bikes ,(sadly i can't buy one even close to the old school bikes)so i will keep mine as close to stock as i can get no pods or headers.
1983 kz 550 m
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
