Valve Adj

  • KZ1911
  • KZ1911's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Valve Adj

06 May 2011 15:54
#449242
Hey all, working on a 1976 kz900,soaked and rebuilt carbs,synced,dyna ignition,and still cant get idle to act right.Air screws seem to react different on each carb.Runs great at all other throttle positions.It has about 22,000 miles.
Could valve clearence be my problem.Or are the carbs just wore out.I really need some help!
1976 KZ 900.
1973 H1 500
2002 Fatboy 104ci.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Valve Adj

06 May 2011 17:08
#449248
KZ1911 wrote: Hey all, working on a 1976 kz900,soaked and rebuilt carbs,synced,dyna ignition,and still cant get idle to act right.Air screws seem to react different on each carb.Runs great at all other throttle positions.It has about 22,000 miles.
Could valve clearence be my problem.Or are the carbs just wore out.I really need some help!
Carbs are not worn out.

Bike is barely broken in at 22,000 miles.

Would definitely check the valve clearances to assure gaps being within factory specs.

An obstructed pilot circuit is often responsible for a poor idle.

Here's a good cleaning method.

Use plenty of carb cleaner spray.
And please wear goggles as the spray always backfires.

If necessary, may also use a small guitar e-string to help clear the several small holes.

If not already done, would also use four brand new NGKB8ES spark plugs, and visually observe a fat blue spark before installing them. And also assure correct ignition timing.

Good Fortune! :)

1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Valve Adj

06 May 2011 20:18
#449286
Tight valve clearance will definitely make it idle rough. Also a vacuum leak or plugged up pilot circuit.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • kawman66
  • kawman66's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 199
  • Thanks: 5

Re: Valve Adj

06 May 2011 20:51
#449299
are the boots the carbs slide into at the head dry rotted.also called intake manifolds.
75 z1b
76 kz900ltd
76 kz900
76 kz900-1500
77 kz1000ltd


my drinking team has a racing problem

Please Log in or Create an account to join the conversation.

  • KZ1911
  • KZ1911's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Re: Valve Adj

06 May 2011 22:27
#449327
All of the boots are new,do you think the valves need adj. at 22,000 miles.
I am not sure how to do this as Patton told me i should check them to make sure.
He is probally right about the pilot curcuit.I did have them sonic cleaned already.
Maybe that did not totally get them cleaned?
1976 KZ 900.
1973 H1 500
2002 Fatboy 104ci.

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: Valve Adj

06 May 2011 22:34
#449330
Just a quick question, did you put a bead of silicone on the mating surface of the intake manifolds to seal them? Pretty sure failing to do so will allow a vacuum leak.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Valve Adj

07 May 2011 00:25
#449357
KZ1911 wrote: All of the boots are new,do you think the valves need adj. at 22,000 miles....

Imo the new carb holders are likely free of air leaks so long as carbs are positioned correctly inside the holders and the clamps are snug.

Air leaks (through carb holders or other sites) usually result in a "racing" idle.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • kawman66
  • kawman66's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 199
  • Thanks: 5

Re: Valve Adj

07 May 2011 00:30
#449359
what exactly is the idle doing.
75 z1b
76 kz900ltd
76 kz900
76 kz900-1500
77 kz1000ltd


my drinking team has a racing problem

Please Log in or Create an account to join the conversation.

  • kawman66
  • kawman66's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 199
  • Thanks: 5

Re: Valve Adj

07 May 2011 00:33
#449360
to check the valves the motor has to be cold as let it sit overnight then pull the valve cover put each lobe on the base of the cam then put a feller gauge under the cam and measure clearance should be .002 to .004 thousands
75 z1b
76 kz900ltd
76 kz900
76 kz900-1500
77 kz1000ltd


my drinking team has a racing problem

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Valve Adj

07 May 2011 01:52
#449375
KZ1911 wrote: All of the boots are new,do you think the valves need adj. at 22,000 miles.
My KZ-750 requires valve check every 3000 miles.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Valve Adj

07 May 2011 02:01
#449377
When hand-rotating the crankshaft to get the cam lobe pointed away from the shim, always use the 17mm "nut" and not the smaller bolt head.

Some folks prefer to loosen or remove the spark plugs during valve clearance work because it's then easier to more precisely hand-rotate the crankshaft using the 17mm nut.

The specified .002"~.004" clearance is same as 0.05mm~0.10mm clearance.
It's usually okay to have slightly over 0.10mm, and up to 0.15mm (especially on the exhaust valves).

But would not run with less than the minimum specified clearance of .002" or 0.05mm.



Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Valve Adj

07 May 2011 02:19
#449379
FSM for KZ900 says valve clearance should be checked every 4000 miles.
However, the clearances often remain within spec for longer distances.

It's typical for clearances to gradually get smaller, until eventually requiring thinner shims to widen the gap between shim and cam.

Existing shims may sometimes be shuffled around to minimize the number of new shims needed.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum